MENU

/
/
Welded pipe straightening method of used welded pipe machines

Welded pipe straightening method of used welded pipe machines

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-01-04 11:30
  • Pvs:

【概要描述】The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.

Welded pipe straightening method of used welded pipe machines

【概要描述】The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-01-04 11:30
  • Pvs:
Detail

The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.

 

Straightening is to use the basic principle of lever (Figure 36) to re-deform the tube in the axial direction, so as to achieve the purpose of straightening.

 

Used welded pipe machines

 

When straightening the pipes of the used welded pipe machines, pay attention to the following requirements.

(1) The force direction avoids the roll edge gap. If the straightening roller is a four-roller structure, the stress point should avoid the gap of the roller edge when straightening, so as to prevent the pipe from drilling into the roller gap and the occurrence of "drilling the pipe" accident. In production, by adjusting the angle of the roller seat, the bottom diameter of the pass of the straightening roller can be the point of stress.

 

(2) Do not participate in sizing. If the outer diameter of the tube is out of tolerance, the straightening roller should not be involved in the sizing adjustment of the tube as much as possible. Especially the straightening structure of the eight-roller type, when it is not adjusted properly, it will have bad consequences in the sizing of the pipe.

 

(3) Adjust the essentials. When the tube is bent, adjust the first set of straightening rollers as far as possible, and adjust less of the one set of straightening rollers at the outlet. When the tube is bent upwards, the inlet roller can be adjusted upwards (Figure 37). If the tube is bent downwards, press the inlet roller down (Figure 38).

 

Used welded pipe machines

 

When the tube is bent to the left or right, the inlet roller can also be adjusted to the left or right. If the used welded pipe machines is still bent after adjustment, or the bending becomes more and more serious, the following six reasons need to be checked item by item.

(1) the pipe swivel;

(2) that the tube is not well cooled, and the welding seam is hot;

(3) the bearing of the straightening roller is damaged;

(4) the straightening roller mechanism is unstable;

(5) the straightening rollers are not attached to the pipe wall;

(6) the parts of the flying saw equipment are in contact with the pipe and become the redundant fulcrum in the adjustment.

 

After solving the above problems, you can obtain satisfactory results by adjusting and straightening.

关键词:

More News

Efficiency optimization of welding process of used high frequency welded pipe production line(2)
Efficiency optimization of welding process of used high frequency welded pipe production line(2)
The high-frequency welding process is the most widely used method for the production of welded pipes by used high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Detail
The high-frequency welding process is the most widely used method for the production of welded pipes by used high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Efficiency optimization of welding process of high frequency welded pipe production line(1)
Efficiency optimization of welding process of high frequency welded pipe production line(1)
The high-frequency welding process is the most widely used method for the production of welded pipes by high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Detail
The high-frequency welding process is the most widely used method for the production of welded pipes by high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Defects caused by improper removal of internal burrs on used welded pipe machine
Defects caused by improper removal of internal burrs on used welded pipe machine
Whether the burr removal process of the used welded pipe machine is appropriate directly affects the quality of the welded pipe. Sometimes grooves are left due to the scraping of the scraper, which is rejected by the user as a welding defect, which brings serious economic losses to the steel pipe manufacturer.
Detail
Whether the burr removal process of the used welded pipe machine is appropriate directly affects the quality of the welded pipe. Sometimes grooves are left due to the scraping of the scraper, which is rejected by the user as a welding defect, which brings serious economic losses to the steel pipe manufacturer.
Analysis of the factors affecting the pipe making process of used high frequency welded pipe equipment (4)
Analysis of the factors affecting the pipe making process of used high frequency welded pipe equipment (4)
The main process parameters of high-frequency straight seam welded pipes manufactured by used high frequency welded pipe equipment include welding heat input, welding pressure, welding speed, size of opening angle, position and size of induction coil, position of impedance and other. These parameters have a great impact on improving the product quality, production efficiency and unit capacity of high-frequency welded pipes. Matching various parameters can make manufacturers obtain considerable economic benefits.
Detail
The main process parameters of high-frequency straight seam welded pipes manufactured by used high frequency welded pipe equipment include welding heat input, welding pressure, welding speed, size of opening angle, position and size of induction coil, position of impedance and other. These parameters have a great impact on improving the product quality, production efficiency and unit capacity of high-frequency welded pipes. Matching various parameters can make manufacturers obtain considerable economic benefits.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn