MENU

/
/
Weld quality failure caused by used welded pipe machines (3)

Weld quality failure caused by used welded pipe machines (3)

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-10-04 11:30
  • Pvs:

【概要描述】When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.

Weld quality failure caused by used welded pipe machines (3)

【概要描述】When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-10-04 11:30
  • Pvs:
Detail

When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.

 

These weld quality failures will occur when the used welded pipe machines is making pipes: ① through-length lap welding. ② Periodic lap welding. ③ Open the seam. ④ Trachoma. ⑤ Peach-shaped tube. ⑥ Weld seam gnawed. ⑦Outer burr planing. ⑧ Heating. ⑨ The current is small. ⑩ Melting of induction coils and electrodes. ⑪ Fire. ⑫ "No high pressure" phenomenon. We can summarize 12 causes of weld quality failures.

 

Used welded pipe machines

 

Slit

Slitting refers to the phenomenon that the welds are not bonded together. The length of the slits is generally more than a few centimeters or even longer. The main reasons are as follows:

 

(1) The hole type is worn. With the wear of the extrusion roll pass, the R dimension of the pass gradually increases. When the hot-rolled steel strip is used as the raw material for the welded pipe, when the width of the steel strip has a negative deviation or the steel is slightly stretched, the quality of the weld will have problems. production. Therefore, it is necessary to constantly check the internal burr of the welded pipe, increase the extrusion amount of the squeeze roller, or replace the new hole type in time.

 

(2) The bearing is damaged. When the bearing of the squeeze roller is only slightly damaged, there will be weld quality problems such as trachoma tubes and lap welded tubes. The seam becomes a fully open shape, accompanied by other quality accidents. At this time, we can also observe the squeeze roller with damaged bearing, and the swing amplitude will become larger as the degree of bearing damage increases.

 

Used welded pipe machines

 

(3) Magnet(resistor). The magnetic bar will form a magnetic field during the welding process of the tube blank, and the high-frequency current can be highly concentrated in the "V"-shaped area of ​​the welding seam, so that the welding seam can reach a high temperature point in a very short time. If there is no magnetic rod in the tube, it will have a great influence on the proximity effect and skin effect of high-frequency current. The most obvious feature is that the welding seam is black and red, without splashing sparks, and the welding seam is fully open. Sometimes even if it is welded, it is false welding, and the popping sound of the horn will occur when the pipe is sizing. If the magnet bar fails or the installation position is not suitable, the welded pipe will burst, even if it does not crack, its strength is very low. At this time, the weld is generally yellow or light blue cracking due to insufficient hot spot temperature.

 

(4) Raw material. Due to the chemical composition of the raw materials, although it is relatively normal during the welding process, the weld will still crack. At this time, the color of the weld is relatively blue, indicating that the temperature is still normal. Sometimes we can see that the crack of the weld deviates from the center of the weld, which is to stick the edge of the base metal to form an irregular seam, which is purely a brittle crack caused by the chemical composition of the raw material.

 

The above is one of the reasons for the quality failure of the welding seam when the used welded pipe machines is making pipes, which is the opening of the seam. The main reasons for the formation of slits are (1) wear of the hole type. (2) The bearing is damaged. (3) Magnetic rod (impedance device). (4) Raw materials.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn