MENU

/
/
Used steel pipe rolling mills, the solution to the difficult forming of thick-walled tube(2)

Used steel pipe rolling mills, the solution to the difficult forming of thick-walled tube(2)

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-10-22 11:30
  • Pvs:

【概要描述】Solutions to solve the difficulties in forming thick-walled tubes of used steel pipe rolling mills include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).

Used steel pipe rolling mills, the solution to the difficult forming of thick-walled tube(2)

【概要描述】Solutions to solve the difficulties in forming thick-walled tubes of used steel pipe rolling mills include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-10-22 11:30
  • Pvs:
Detail

Solutions to solve the difficulties in forming thick-walled tubes of used steel pipe rolling mills include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).

 

Used steel pipe rolling mills

 

Dedicated forming unit solution

The used steel pipe rolling mills can be divided into large and medium-sized welded pipe mills or special thick-walled pipe mills. Most of them are equipped with edge planers or milling machines. Before the flat tube billet enters the first forming flat roll, the raw material edge is planed and milled in advance. Realize parallel butt joints of welds. This scheme is relatively mature and applied in the welded pipe industry. The disadvantage is that the investment is large, especially for small welded pipe units, which is relatively large.

 

Rough forming pass solution

The basic idea of applying the edge double-radius W hole type to solve the difficulties of thick-walled pipe forming is to respect the deformation characteristics of thick-walled pipe’s wide deformation blind zone, large springback and large difference between inner and outer circumferences, and implement the implementation of the billet within the range of several times the deformation blind zone. Excessive deformation. In other words, if there is no deformation blind zone and springback, the formed tube will show a ∧-shaped butt state; when the deformed tube blank has a deformation blind zone and springback, it will just reach a parallel butt state. In this way, although the deformation blind zone cannot be eliminated, the edge V-shaped butt joint can be eliminated, and the process goal of the parallel butt joint of the weld seam can be achieved. The double-radius W hole pattern at the edge can eliminate the influence of the V-shaped opening of the thick-walled pipe deformation dead zone and its springback on the welding while the deformation dead zone still exists, realize the parallel butt joint of the welds, and ensure the forming of the thick-walled pipe from the deformation process. quality.

 

For the used steel pipe rolling mills, four solutions are proposed for the forming difficulties of thick-walled pipes. According to the actual situation, the corresponding solutions are used to solve them. I hope to provide you with effective help.

 

Part of the content of this site comes from the Internet. This site only provides information storage. The copyright belongs to the original author. It does not bear the relevant legal responsibility and does not represent the views and positions of this site. Please contact and delete it if there is any infringement.

 

关键词:

More News

Welded pipe straightening method of used welded pipe machines
Welded pipe straightening method of used welded pipe machines
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Detail
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Common faults of used welded pipe units
Common faults of used welded pipe units
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Detail
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn