MENU

/
/
Used ERW tube mills, how to adjust the squeeze roll "up one next two"

Used ERW tube mills, how to adjust the squeeze roll "up one next two"

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-01-28 11:30
  • Pvs:

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

Used ERW tube mills, how to adjust the squeeze roll "up one next two"

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-01-28 11:30
  • Pvs:
Detail

When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

 

Used ERW tube mills

 

Although the "up one down two" three-roller extrusion method has the characteristics of independent adjustment, three-roller unified adjustment, overall rotation and easy adjustment of the It covers 120 degrees, and the diameter and load capacity of each roller is effectively reduced, which avoids many of the disadvantages of the two-roller and the top three-roller. However, it is still impossible to avoid the existence of the independent top-roller three-roll squeeze mode. Shortcomings. Because of the small roll diameter of the used ERW tube mills, its bypass current is much smaller than that of the "two on one side" top roll extrusion device. However, equipment manufacturing also has the problems of relatively high technical requirements, processing accuracy requirements and relatively high cost, and relatively difficult adjustments. Only a few manufacturers currently use it.

 

The above is the method of adjusting the squeeze roll of the used ERW tube mills "up one down two", the next issue will introduce the method ④ "two top rolls and two side vertical rolls". If you need it, you can pay attention to the method in the next issue. At the same time, if you need used welded pipe equipments, please contact us. You only need to inform us of your pipe-making needs, and our company will provide you with used welded pipe equipments that really suits your needs.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Analyzing the roll life of a used ERW tube mill
Analyzing the roll life of a used ERW tube mill
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Detail
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
How to extend the service life of high frequency welded pipe equipment
How to extend the service life of high frequency welded pipe equipment
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Detail
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Detail
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn