MENU

/
/
How to adjust the opening angle of used welded pipe machine

How to adjust the opening angle of used welded pipe machine

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-07-03 11:30
  • Pvs:

【概要描述】When adjusting the pipe opening angle of used welded pipe machine, the following 4 basic methods should be followed.

How to adjust the opening angle of used welded pipe machine

【概要描述】When adjusting the pipe opening angle of used welded pipe machine, the following 4 basic methods should be followed.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-07-03 11:30
  • Pvs:
Detail

When adjusting the pipe opening angle of used welded pipe machine, the following 4 basic methods should be followed.

 

(1) Wall thickness method. It means that the opening angle should be reduced as much as possible when producing thick-walled pipes, and the opening angle should be appropriately increased when using used welded pipe machine to produce thin-walled pipes.

 

(2) The natural way. That is, as the guide ring and the hole pattern are naturally worn out, the guide roller is pressed down in stages, so that the opening angle will decrease accordingly; after the new guide ring is replaced, the opening angle should be restored to the original state.

 

Used welded pipe machine

(3) Micro-deformation method. In theory, the guide roller does not undertake the task of deformation; however, starting from the actual need to stabilize the opening angle, it is necessary to allow the guide roller to undertake the slight deformation limited to the control of springback.

 

(4) Efficiency method. In order to improve the power utilization efficiency and production efficiency, the opening angle must be adjusted as small as possible when the process conditions permit.

 

The four basic ways to adjust the opening angle of the pipe made by used welded pipe machine must be adjusted according to the actual situation of the opening angle.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn