MENU

/
/
Correct selection of induction coils for used high frequency welded pipe equipment

Correct selection of induction coils for used high frequency welded pipe equipment

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-07-02 11:30
  • Pvs:

【概要描述】For used high frequency welded pipe equipment in order to obtain the maximum welding efficiency, the correct selection of the induction coil is very important.

Correct selection of induction coils for used high frequency welded pipe equipment

【概要描述】For used high frequency welded pipe equipment in order to obtain the maximum welding efficiency, the correct selection of the induction coil is very important.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-07-02 11:30
  • Pvs:
Detail

For used high frequency welded pipe equipment in order to obtain the maximum welding efficiency, the correct selection of the induction coil is very important.

 

Used high frequency welded pipe equipment to make high-frequency welded pipe production process parameters include welding speed (unit speed), welding temperature (high-frequency power), welding current (high-frequency frequency), extrusion force (mold design and material), opening V Angle, the size and position of the inductor (material of the coil, winding direction, position) and impedance (magnetic rod).

 

Used high frequency welded pipe equipment

 

The distance A between the coil and the squeeze roll depends on the design of the rolling mill and the diameter of the squeeze roll. The smaller A is, the better, and it is best not to exceed the pipe diameter, as shown in the figure above.

 

The inner diameter of the coil and its length should be equal and approximately 20% larger than the pipe diameter

 

Used high frequency welded pipe equipment

 

High frequency (stable and continuous) power, welding speed, welding extrusion force and opening V angle are the most important process parameters, which must be matched reasonably, otherwise it will affect the welding quality.

 

Adjust the production speed of used high frequency welded pipe equipment. If the speed is too high or too low, it will cause low-temperature welding impermeability and high-temperature overburning, and the weld will crack after being flattened.

 

When the squeezing force is insufficient, the edge metals to be welded cannot be completely pressed together, the impurities remaining in the weld are not easily discharged, and the strength is reduced. When the extrusion force is too large, the metal flow angle increases, the residue is easily discharged, the heat-affected zone becomes narrow, and the welding quality is improved. However, if the pressure is too high, it will cause larger sparks and splashes, causing the molten oxide and part of the metal plastic layer to be squeezed out, and the weld will become thinner after being scratched, thereby reducing the strength of the weld. Proper extrusion force is an important prerequisite to ensure welding quality.

 

The opening angle is too large, which reduces the high-frequency proximity effect, increases the power loss, and reduces the welding temperature. If the welding speed does not change, the welding will be impenetrable; if the opening angle is too small, the welding current will be unstable, and small splashes will occur at the squeezing point.

 

The induction coil is an important part of the production of high-frequency welded pipes. The gap between it and the pipe blank and the width of the opening have a great influence on the welding quality.

 

The gap between the induction coil and the tube blank is too large, resulting in a sharp drop in inductance efficiency;

If the gap between the induction coil and the tube blank is too small, it is easy to generate electric discharge between the coil and the tube blank, and it is also easy to be damaged by the moving tube blank.

 

If the width of the induction coil is too large, the welding temperature of the butt edge of the tube blank will be reduced. If the welding speed is fast, false welding and cracking are likely to occur after straightening.

 

Part of the content of this site comes from the Internet. This site only provides information storage. The copyright belongs to the original author. It does not bear the relevant legal responsibility and does not represent the views and positions of this site. Please contact and delete it if there is any infringement.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn