MENU

/
/
High frequency welded pipe machine on the impact of welded tube blank defects on the quality of welded tube (6)

High frequency welded pipe machine on the impact of welded tube blank defects on the quality of welded tube (6)

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-10-01 11:30
  • Pvs:

【概要描述】The dominant defects of the welded tube blank of the high frequency welded pipe machine generally include cracked edges, broken edges, sawtooth, pitting, scratches, roll marks, dark spots, edge burrs, sickle bends, wrinkles, waves, edge warping, and points. Layers, warped skins, pinholes, sticky rolls, soft spots, rust, oxide layers, towers, loose rolls, etc. Let me introduce you to the causes of cracked edges and the effect of cracked edge billets on welded pipes.

High frequency welded pipe machine on the impact of welded tube blank defects on the quality of welded tube (6)

【概要描述】The dominant defects of the welded tube blank of the high frequency welded pipe machine generally include cracked edges, broken edges, sawtooth, pitting, scratches, roll marks, dark spots, edge burrs, sickle bends, wrinkles, waves, edge warping, and points. Layers, warped skins, pinholes, sticky rolls, soft spots, rust, oxide layers, towers, loose rolls, etc. Let me introduce you to the causes of cracked edges and the effect of cracked edge billets on welded pipes.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-10-01 11:30
  • Pvs:
Detail

If the high frequency welded pipe machine refers to the chemical composition and mechanical properties of welded tube blanks that require certain inspection methods to be known as invisible defects; then, those defects that can be seen only by vision are called tube blanks. Overt defect.

 

The dominant defects of the welded tube blank of the high frequency welded pipe machine generally include cracked edges, broken edges, sawtooth, pitting, scratches, roll marks, dark spots, edge burrs, sickle bends, wrinkles, waves, edge warping, and points. Layers, warped skins, pinholes, sticky rolls, soft spots, rust, oxide layers, towers, loose rolls, etc. Let me introduce you to the causes of cracked edges and the effect of cracked edge billets on welded pipes.

 

High frequency welded pipe machine

 

Sickle bend

The sickle elbow refers to the phenomenon of lateral bending of the tube blank. The standard stipulates that the sickle bend of the hot-rolled tube shall be no more than 3mm/m, and that of the cold-rolled tube shall be no more than 2mm/m. The possibility of hot-rolled narrow tube blanks without trimming is the greatest.

 

The reason for the sickle bend:

(1) The reduction of both ends of the roll fluctuates during the production of tube blanks.

(2) The temperature difference between the two sides of the strip is large when the strip is rolled.

(3) The receiving device of the slitting machine is inconsistent with the center of the tension station and the shearing machine.

 

High frequency welded pipe machine

 

The influence of sickle bend on welded pipe production:

(1) During the molding process, the long side will be "surplus", which is easy to produce a molding bulge.

(2) "Lap welding" or dislocation of the weld seam is easy to occur during the welding process, and the weld seam strength cannot be guaranteed.

(3) Welding seam swings left and right, it is not easy to control the depth of external burr removal.

(4) The forming forces on both sides of the sickle elbow tube blank are different. During the forming and deformation process, the tube blank has a tendency to bend forward, and the formed tube blank is prone to "off-track", causing production to stop.

 

High frequency welded pipe machine

 

About the high frequency welded pipe machine welded tube defects (6) the introduction of the sickle bend, and the influence of the sickle bend on the quality of the welded pipe, I hope it can help you.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Detail
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn