MENU

/
/
Used square pipe machines, the method of inspecting and manufacturing square rectangular tube

Used square pipe machines, the method of inspecting and manufacturing square rectangular tube

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-02 11:30
  • Pvs:

【概要描述】How to adjust the square of the square tube machine in the used square tube machines is to check whether the square tube square is qualified through correct measurement and judgment.

Used square pipe machines, the method of inspecting and manufacturing square rectangular tube

【概要描述】How to adjust the square of the square tube machine in the used square tube machines is to check whether the square tube square is qualified through correct measurement and judgment.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-02 11:30
  • Pvs:
Detail

How to adjust the square of the square tube machine in the used square tube machines is to check whether the square tube square is qualified through correct measurement and judgment.

 

Before adjusting the square tube square of the used square tube machines, let's talk about the square tube square measurement.

 

Used square pipe machines

 

The prerequisite for adjusting the square tube is correct measurement and judgment. There are three methods for detecting the square of the square tube:

 

(1) The diagonal method. Make the diagonals equal, but as described in the Rectangular Tube Adjustment-Diagonal section, the confidence of diagonal measurement is not high due to the actual size of the r angle and the measurement position.

 

(2) Square measurement method. Place one side of the square against the tube surface and move it up and down until the other side touches any point on the tube surface to check for light leakage. However, this measurement method has a prerequisite, that is, the measurement surface must be flat, emphasizing rather concave than convex.

 

(3) "Twin Inspection Method". When you don’t have a square on hand, you can cut two sections of pipe heads from the same rectangular tube. After cleaning the end burrs, place them on the platform facing each other or opposite (marked by the weld seam), and then slowly approach them. The position behind the gap determines the square of the tube.

 

Three methods are used to detect whether the square tube made by the used square tube machines is square, which is mainly reflected in the diagonal method, the square measurement method, and the twin inspection method.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Analyzing the roll life of a used ERW tube mill
Analyzing the roll life of a used ERW tube mill
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Detail
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
How to extend the service life of high frequency welded pipe equipment
How to extend the service life of high frequency welded pipe equipment
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Detail
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Detail
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn