MENU

/
/
The scheme of placing the impedance in the used high frequency welded pipe equipment

The scheme of placing the impedance in the used high frequency welded pipe equipment

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-05-04 11:30
  • Pvs:

【概要描述】Most literatures use two positioning datums when describing the scheme of placing the impedance in the used high frequency welded pipe equipment, one is based on the contour of the impedance, and the other is based on the contour of the magnetic rod inside the impedance. There are certain differences between the two benchmarks.

The scheme of placing the impedance in the used high frequency welded pipe equipment

【概要描述】Most literatures use two positioning datums when describing the scheme of placing the impedance in the used high frequency welded pipe equipment, one is based on the contour of the impedance, and the other is based on the contour of the magnetic rod inside the impedance. There are certain differences between the two benchmarks.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2023-05-04 11:30
  • Pvs:
Detail

Most literatures use two positioning datums when describing the scheme of placing the impedance in the used high frequency welded pipe equipment, one is based on the contour of the impedance, and the other is based on the contour of the magnetic rod inside the impedance. There are certain differences between the two benchmarks.

 

Used high frequency welded pipe equipment

 

In the induction welding process, the induced current of the welded pipe blank is mainly distributed near the inner and outer perimeter edges of the fusion surface of the pipe blank. The current density in other areas of the tube blank is lower.

 

A large number of experiments show that under the premise of placing the magnetic rod (impedance device), the current density is high in the interval from the center line of the squeeze roller to the front end of the induction coil; in the induction coil area, the current density decreases rapidly, and after the induction coil At the end position, the current density drops to 3% of the peak value. After removing the magnetic rod (resistor) in the tube blank, the current density on the edge of the tube blank dropped significantly, and the average drop of the current density in front of the induction coil was about 47%.

 

Placing a magnet bar in the tube blank can make the induced current in the tube blank gather on the fusion surface, improve the current density on the edge of the tube blank on the fusion surface, thereby improving the induction welding efficiency and saving the power of the used high frequency welded pipe equipment. If the magnet bar is not used or the magnet bar fails, it will take more power to maintain production.

 

It should be noted that if the magnetic rod is packaged inside the resistor, there should be a certain distance between the front end of the resistor and the front end of the magnetic rod. In some literatures, the front of the resistor is placed as the benchmark, and the front end of the resistor is aligned with the center end of the squeeze roller line, so that the front of the magnet bar may be located behind the center line of the squeeze roller, which will reduce the high welding efficiency. The magnet bar in the resistor is an important part that affects the distribution of the induced current. When placing the resistor, the outline of the magnet bar should be used as the benchmark.

 

Used high frequency welded pipe equipment

 

Practical experience suggests that the length of the bar magnet should be 3.5 times the width of the induction coil, but this view is less general. When determining the length of the magnet bar, it should be based on the distribution of the induced current in the axial direction of the welded pipe. In the induction welding process of used high frequency welded pipe equipment, the induced current is mainly distributed in the interval from the center line of the squeeze roller to the rear end of the induction coil. Aligning the front end of the magnetic bar with the center line of the extrusion roller, and the rear end of the magnetic bar and the back end of the induction coil coincide, so that most of the induced current in the tube blank can be concentrated on the fusion surface of the welded tube by the action of the magnetic bar. The minimum length of the magnet bar can be determined according to the position of the front and rear ends of the induction coil.

 

Overview:

When placing the impedance, it should be based on the outline of the magnetic rod inside the impedance. In the axial direction of the welded pipe, it is necessary to align the front end of the magnetic bar with the centerline of the squeeze roller. If the front end of the magnet bar is located behind the centerline of the squeeze roller, the induction welding efficiency will be reduced. The length of the magnet bar should not be less than the distance from the center line of the squeeze roller to the rear end of the induction coil.

 

In the vertical direction of the cross-section of the welded pipe, the resistance of the resistor close to the fusion surface of the welded pipe can improve the efficiency of induction welding. The cross-sectional area of the magnetic rod inside the impedance device can meet the production requirements when the cross-sectional area of the inner wall of the welded pipe is over 50%.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn