Used Pipe Mill Supplier
The reason of the surface defect of the tube blank caused by the welding extrusion roller of the directly forming to square pipe mills
- Sort：Information
- Auth:
- Source:
- Release time：2023-08-18 11:30
- Pvs：
【概要描述】When directly forming to square pipe mills during operation and welding, the problem of the surface defect of the tube blank caused by the squeeze roller is often caused, and then the reason for the surface defect of the tube blank is caused.
The reason of the surface defect of the tube blank caused by the welding extrusion roller of the directly forming to square pipe mills
【概要描述】When directly forming to square pipe mills during operation and welding, the problem of the surface defect of the tube blank caused by the squeeze roller is often caused, and then the reason for the surface defect of the tube blank is caused.
- Sort：Information
- Auth:
- Source:
- Release time：2023-08-18 11:30
- Pvs：
Detail
When directly forming to square pipe mills during operation and welding, the problem of the surface defect of the tube blank caused by the squeeze roller is often caused, and then the reason for the surface defect of the tube blank is caused.
The squeeze roll directly forming to square pipe mills causes the surface defects of the tube blank during welding. The main factor is the position and type of the defect, which can be divided into 6 types.
1. The inner roll edge of the upper squeeze roll causes linear indentation on the tube blank
Reasons: ①The upper squeeze roll is too large to press down, and the flat ellipse of the tube blank is larger than the vertical ellipse; ②The hole radius of the upper squeeze roll is too large.
2. The inner roller edge of the upper squeeze roller presses the outer burr into the tube blank to form a pit
Reasons: ①The gap of the upper squeeze roller is too small; ②The center of the upper squeeze roller is offset; ③The crescent or bulge of the raw material is large and the forming is unstable.
3. The outer edge of the upper squeeze roller causes linear indentation on the tube blank
Reasons: ①The bearing of the upper squeeze roller is severely worn or damaged; ②The hole radius of the upper squeeze roller is too small; ③The flat ellipse of the tube blank is larger than the vertical ellipse; ④The center position of the upper squeeze roller is offset from the center of the unit.
4. The upper roll edge of the side squeeze roll causes linear indentation on the tube blank
Reasons: ①The side squeeze roller is low or inclined; ②The center of the side squeeze roller is offset from the center of the unit; ③The escape angle of the upper part of the side squeeze roller is too small; Larger than flat oval; ⑤The upper squeeze roller is insufficiently pressed.
5. The lower edge of the side squeeze roller causes linear indentation or crescent-shaped scratches on the tube blank
Reason: ①The side squeeze roller is too high; ②The center of the side squeeze roller is offset from the center of the unit; ③The escape angle of the bottom of the side squeeze roller is too small; Partially scratched.
6. The roll edge of the lower roll causes linear indentation on the tube blank
Reasons: ①The bottom roll is too high, the bottom roll is inclined or the side squeeze roll is too low; ②The center of the bottom roll is off the center of the unit; ③The escape angle of the bottom roll is too small; ④The side squeeze roll is insufficiently squeezed and the tube blank is larger Li oval.
After analyzing the main reasons for the indentation and scratches of the squeeze roller, it is found that any parameter is not isolated. The change of any parameter will affect other parameters, for example, in order to eliminate the upper edge of the side squeeze roller on the tube blank. Pressing the upper squeeze roller down due to the indentation will cause the welding squeeze force to increase, the squeeze amount becomes larger, and the butt joint shape changes. Therefore, after the indentation or scratch occurs when directly forming to square pipe mills, the cause should be carefully analyzed, and various effects must be comprehensively considered when processing. According to the above method, the squeeze roller of the unit is optimized and adjusted to eliminate the indentation and scratches caused by the squeeze roller to the tube blank, and the surface of the tube blank is smooth.
关键词：
More News
The personnel training of spiral welding pipe machine
Time of issue : 2024-12-06
1.Equipment introduction and Basic principles:
The composition of the equipment and the function description of each part.
The production principle of spiral welded pipe, including the basic process of forming, welding and shaping steel strip.
2.Safe operation rules and regulations:
Explain safe operation procedures in detail.
Emphasis on the use of personal protective equipment.
Safe operation procedures for equipment start-up, operation and shutdown.
3.Equipment Operation Training:
How to properly start and shut down the device.
Loading and centering adjustment method of steel belt.
Set and adjust welding current and voltage.
How to control production speed and quality control.
4.Common fault diagnosis and treatment:
Common fault identification and elimination methods.
Diagnosis and countermeasures of welding defects.
Routine maintenance and maintenance of equipment.
5.Quality Control:
How to ensure the stability and consistency of welding.
Methods to detect and test the quality of welded pipes, such as ultrasonic inspection, X-ray inspection, etc.
6. Hands-on Training:
Training and guidance in actual operation to ensure that trainees can operate the equipment independently.
Simulate problem handling and emergency response in a production environment.
7.Theoretical and practical evaluation:
Assess the theoretical knowledge and practical skills of the trainees to ensure that they meet the training requirements.
Training is usually conducted by experienced technicians and engineers and includes both detailed written information and field practice. After the training, there may be a corresponding certification or certificate issued as a sign that the operator is qualified.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
1.Equipment introduction and Basic principles:
The composition of the equipment and the function description of each part.
The production principle of spiral welded pipe, including the basic process of forming, welding and shaping steel strip.
2.Safe operation rules and regulations:
Explain safe operation procedures in detail.
Emphasis on the use of personal protective equipment.
Safe operation procedures for equipment start-up, operation and shutdown.
3.Equipment Operation Training:
How to properly start and shut down the device.
Loading and centering adjustment method of steel belt.
Set and adjust welding current and voltage.
How to control production speed and quality control.
4.Common fault diagnosis and treatment:
Common fault identification and elimination methods.
Diagnosis and countermeasures of welding defects.
Routine maintenance and maintenance of equipment.
5.Quality Control:
How to ensure the stability and consistency of welding.
Methods to detect and test the quality of welded pipes, such as ultrasonic inspection, X-ray inspection, etc.
6. Hands-on Training:
Training and guidance in actual operation to ensure that trainees can operate the equipment independently.
Simulate problem handling and emergency response in a production environment.
7.Theoretical and practical evaluation:
Assess the theoretical knowledge and practical skills of the trainees to ensure that they meet the training requirements.
Training is usually conducted by experienced technicians and engineers and includes both detailed written information and field practice. After the training, there may be a corresponding certification or certificate issued as a sign that the operator is qualified.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
Conduct training of slitting crew
Time of issue : 2024-12-05
1.Theoretical Training:
Equipment knowledge: Understand the basic components of the slitting unit and its working principle.
Operation specifications: Familiar with the operation procedures, including starting, stopping, adjusting parameters, common problem handling, etc.
Safety training: Understand the safety risks in equipment operation and corresponding preventive measures, and be familiar with emergency handling methods in emergency situations.
2.Practical operation:
On-site operation demonstration: An experienced operator gives a demonstration on site to guide new employees to master basic operating skills.
Hands-on practice: Let new employees operate the equipment themselves, accumulate experience in actual operation, and solve the problems encountered.
3.Maintenance:
Daily inspection: Train employees to understand the contents and methods of daily inspection of equipment, including cleaning, lubrication, fastening and other work.
Troubleshooting: Teach employees how to identify common equipment failures, understand basic troubleshooting methods and when professional maintenance personnel are required to intervene.
4.Efficiency optimization:
Production Management: Explain how to rationally arrange production tasks to improve equipment utilization and production efficiency.
Data Analysis: Teach employees how to record and analyze production data to find and improve the weak links in production.
5.Assessment and continuous improvement:
Assessment: Evaluate the effectiveness of training through examinations or practical assessments to ensure that employees have the necessary knowledge and skills.
Continuous improvement: Regularly organize training review and skill upgrading courses, and constantly improve the training content according to the actual production and equipment update.
After the training, new employees can work under the supervision of an experienced operator until they are fully competent.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
1.Theoretical Training:
Equipment knowledge: Understand the basic components of the slitting unit and its working principle.
Operation specifications: Familiar with the operation procedures, including starting, stopping, adjusting parameters, common problem handling, etc.
Safety training: Understand the safety risks in equipment operation and corresponding preventive measures, and be familiar with emergency handling methods in emergency situations.
2.Practical operation:
On-site operation demonstration: An experienced operator gives a demonstration on site to guide new employees to master basic operating skills.
Hands-on practice: Let new employees operate the equipment themselves, accumulate experience in actual operation, and solve the problems encountered.
3.Maintenance:
Daily inspection: Train employees to understand the contents and methods of daily inspection of equipment, including cleaning, lubrication, fastening and other work.
Troubleshooting: Teach employees how to identify common equipment failures, understand basic troubleshooting methods and when professional maintenance personnel are required to intervene.
4.Efficiency optimization:
Production Management: Explain how to rationally arrange production tasks to improve equipment utilization and production efficiency.
Data Analysis: Teach employees how to record and analyze production data to find and improve the weak links in production.
5.Assessment and continuous improvement:
Assessment: Evaluate the effectiveness of training through examinations or practical assessments to ensure that employees have the necessary knowledge and skills.
Continuous improvement: Regularly organize training review and skill upgrading courses, and constantly improve the training content according to the actual production and equipment update.
After the training, new employees can work under the supervision of an experienced operator until they are fully competent.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
Looper motors are commonly used in steel rolling lines in the metalworking industry
Time of issue : 2024-12-04
1.Installation and commissioning:
Position selection: According to the layout and process requirements of the production line, the installation position of the looping clip motor is reasonably selected.
Fixed and connected: Install the motor firmly in the designated position, and connect it with the corresponding mechanical transmission components.
Electrical wiring: Correct wiring to ensure reliable connection between the motor and the control system.
2.Start and Stop:
Check before starting: Check the lubrication state of the motor and transmission parts, whether the fasteners are loose, and whether the electrical line is normal.
Smooth start: When starting the motor, it should avoid the impact of instantaneous large current, and use soft start or frequency conversion start.
Normal shutdown: The shutdown should gradually reduce the speed of the motor to prevent sudden stop from impacting the equipment.
3.Operation and control:
Constant tension: The tension control system is used to maintain a constant tension during the operation of the looping motor to avoid strip relaxation or pulling.
Speed synchronization: Adjust the running speed of the motor according to the process requirements, so that it matches the speed of the equipment before and after the process.
Feedback control: Through the sensor and feedback system, real-time monitoring of the motor operating status, adjust the parameters to ensure the stable operation of the production line.
4.Maintenance and maintenance:
Regular inspection: Regularly check the wear of the motor and transmission parts, and replace the damaged parts in time.
Lubrication maintenance: Regular lubrication maintenance of mechanical parts to ensure their good operation.
Clean and dust-proof: Keep the motor and control cabinet clean to prevent dust and debris from entering, affecting the performance of the equipment.
5.Troubleshooting:
Fault diagnosis: When there is a fault, professional detection equipment is used to diagnose the motor and determine the cause of the fault.
Timely repair: Repair or replace the fault part according to the diagnosis results to ensure that the equipment returns to normal work as soon as possible.
In short, the correct use and maintenance of the looper clip motor is crucial to ensure the efficient and stable operation of the metal processing line.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
1.Installation and commissioning:
Position selection: According to the layout and process requirements of the production line, the installation position of the looping clip motor is reasonably selected.
Fixed and connected: Install the motor firmly in the designated position, and connect it with the corresponding mechanical transmission components.
Electrical wiring: Correct wiring to ensure reliable connection between the motor and the control system.
2.Start and Stop:
Check before starting: Check the lubrication state of the motor and transmission parts, whether the fasteners are loose, and whether the electrical line is normal.
Smooth start: When starting the motor, it should avoid the impact of instantaneous large current, and use soft start or frequency conversion start.
Normal shutdown: The shutdown should gradually reduce the speed of the motor to prevent sudden stop from impacting the equipment.
3.Operation and control:
Constant tension: The tension control system is used to maintain a constant tension during the operation of the looping motor to avoid strip relaxation or pulling.
Speed synchronization: Adjust the running speed of the motor according to the process requirements, so that it matches the speed of the equipment before and after the process.
Feedback control: Through the sensor and feedback system, real-time monitoring of the motor operating status, adjust the parameters to ensure the stable operation of the production line.
4.Maintenance and maintenance:
Regular inspection: Regularly check the wear of the motor and transmission parts, and replace the damaged parts in time.
Lubrication maintenance: Regular lubrication maintenance of mechanical parts to ensure their good operation.
Clean and dust-proof: Keep the motor and control cabinet clean to prevent dust and debris from entering, affecting the performance of the equipment.
5.Troubleshooting:
Fault diagnosis: When there is a fault, professional detection equipment is used to diagnose the motor and determine the cause of the fault.
Timely repair: Repair or replace the fault part according to the diagnosis results to ensure that the equipment returns to normal work as soon as possible.
In short, the correct use and maintenance of the looper clip motor is crucial to ensure the efficient and stable operation of the metal processing line.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
Apply of Bedroom screw looping
Time of issue : 2024-12-03
1.Basic construction: A typical roller type bedroom spiral hoop usually consists of two sets of rollers that form a spiral shaped channel for guiding and supporting the metal strip.
2.Operation principle: When the metal strip passes through the looper, the strip is guided and supported in the spiral path. Due to the spiral structure of the looper, the strip can be smoothly transmitted under the condition of uneven strip speed to ensure the normal progress of the subsequent process.
3.Commissioning and maintenance: Used equipment needs to be inspected and maintained in detail before use. Includes:
Cleaning: Remove oil, dust and so on from the surface.
Lubrication: Check and add lubricating oil to ensure the normal operation of each transmission component.
Calibration: Ensure that the neutralization pressure of the roller is set correctly.
Replacement parts: Check for wear and replace necessary parts.
4.Application process: In the process of use, it is necessary to pay attention to the operation specifications, monitor the operating status of the equipment, and adjust the equipment parameters in time to meet the strip specifications and process requirements. In addition, it is also necessary to pay attention to safe operation to prevent accidents.
Through the above methods, the used roller bedroom spiral looper can continue to play its function and provide support for metal processing production.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
1.Basic construction: A typical roller type bedroom spiral hoop usually consists of two sets of rollers that form a spiral shaped channel for guiding and supporting the metal strip.
2.Operation principle: When the metal strip passes through the looper, the strip is guided and supported in the spiral path. Due to the spiral structure of the looper, the strip can be smoothly transmitted under the condition of uneven strip speed to ensure the normal progress of the subsequent process.
3.Commissioning and maintenance: Used equipment needs to be inspected and maintained in detail before use. Includes:
Cleaning: Remove oil, dust and so on from the surface.
Lubrication: Check and add lubricating oil to ensure the normal operation of each transmission component.
Calibration: Ensure that the neutralization pressure of the roller is set correctly.
Replacement parts: Check for wear and replace necessary parts.
4.Application process: In the process of use, it is necessary to pay attention to the operation specifications, monitor the operating status of the equipment, and adjust the equipment parameters in time to meet the strip specifications and process requirements. In addition, it is also necessary to pay attention to safe operation to prevent accidents.
Through the above methods, the used roller bedroom spiral looper can continue to play its function and provide support for metal processing production.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province
Recommendation
Online Inquiry
底部留言
描述：
LINK
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Contact Us
Tel (wechat): 13336487288
Wechat：+86 13336487288
WhatsApp:+86 13336487288
Email: zty@usedpipemill.com
Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province
