MENU

/
/
How to adjust the extrusion roll "up one next two" of the used ERW tube mills

How to adjust the extrusion roll "up one next two" of the used ERW tube mills

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-11-28 11:30
  • Pvs:

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

How to adjust the extrusion roll "up one next two" of the used ERW tube mills

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-11-28 11:30
  • Pvs:
Detail

When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

 

Used ERW tube mills

 

Although the "up one down two" three-roller extrusion method has the characteristics of independent adjustment, three-roller unified adjustment, overall rotation and easy adjustment of the It covers 120 degrees, and the diameter and load capacity of each roller is effectively reduced, which avoids many of the disadvantages of the two-roller and the top three-roller. However, it is still impossible to avoid the existence of the independent top-roller three-roll squeeze mode. Shortcomings. Because of the small roll diameter of the used ERW tube mills, its bypass current is much smaller than that of the "two on one side" top roll extrusion device. However, equipment manufacturing also has the problems of relatively high technical requirements, processing accuracy requirements and relatively high cost, and relatively difficult adjustments. Only a few manufacturers currently use it.

 

Used ERW tube mills

 

The above is the method of adjusting the squeeze roll of the used ERW tube mills "up one down two", the next issue will introduce the method ④ "two top rolls and two side vertical rolls". If you need it, you can pay attention to the method in the next issue. At the same time, if you need used welded pipe equipments, please contact us. You only need to inform us of your pipe-making needs, and our company will provide you with used welded pipe equipments that really suits your needs.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Detail
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn