MENU

/
/
Used ERW tube mills, how to adjust the squeeze roll "up two next one"

Used ERW tube mills, how to adjust the squeeze roll "up two next one"

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-01-25 11:30
  • Pvs:

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up, two, next" is one of the squeeze roll methods.

Used ERW tube mills, how to adjust the squeeze roll "up two next one"

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up, two, next" is one of the squeeze roll methods.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-01-25 11:30
  • Pvs:
Detail

When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up, two, next" is one of the squeeze roll methods.

 

Used ERW tube mills

 

The "up two next one" three-roll extrusion method can be said to be the best extrusion method for small pipe diameter welding (steel pipes below 114mm) in the used ERW tube mills. Three-roller independent adjustment, three-roller unified adjustment and overall rotation make the adjustment consistent. The three squeezing rollers each cover nearly 120 degrees, and the diameter and load-bearing capacity of each roller are effectively reduced. Vee length = pipe diameter, which is the most efficient. The upper two rollers effectively fit the edges of the steel strip in an angle form, forming a good squeezing force and controlling the edges of the steel strip. Many disadvantages of the two-roller and the top three-roller are avoided, so it is an ideal welding extrusion device.

 

The disadvantage is that the technical requirements, processing accuracy requirements and cost are relatively high, and adjustments are more difficult at the same time, which limits the promotion. It is usually used on steel pipe lines with higher requirements.

 

Used ERW tube mills

 

Used ERW tube mills

 

The above is the method of adjusting the squeeze roll of the used ERW tube mills "up two next one", the next issue will introduce the second method "up one next two". If you need it, you can pay attention to the method in the next issue. At the same time, if you need second-hand welded pipe equipment, please contact us. You only need to inform us of your pipe-making needs, and our company will provide you with used welded pipe equipments that really suits your needs.

关键词:

More News

Welded pipe straightening method of used welded pipe machines
Welded pipe straightening method of used welded pipe machines
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Detail
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Common faults of used welded pipe units
Common faults of used welded pipe units
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Detail
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn