MENU

/
/
Used ERW tube mills, how to adjust the squeeze roll "Two Top Rollers, Two Side Vertical Rollers and One Bottom Roller"

Used ERW tube mills, how to adjust the squeeze roll "Two Top Rollers, Two Side Vertical Rollers and One Bottom Roller"

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-02-03 11:30
  • Pvs:

【概要描述】When the used ERW tube mills is used to make welded pipes, it is necessary to rely on the control of the squeeze roller to judge the quality of the welded pipe to be qualified. Therefore, the control of the squeeze roller is very important. There are many ways to control the squeeze roll, "two top rolls, two side vertical rolls and one bottom roll" is one of the squeeze roll methods.

Used ERW tube mills, how to adjust the squeeze roll "Two Top Rollers, Two Side Vertical Rollers and One Bottom Roller"

【概要描述】When the used ERW tube mills is used to make welded pipes, it is necessary to rely on the control of the squeeze roller to judge the quality of the welded pipe to be qualified. Therefore, the control of the squeeze roller is very important. There are many ways to control the squeeze roll, "two top rolls, two side vertical rolls and one bottom roll" is one of the squeeze roll methods.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-02-03 11:30
  • Pvs:
Detail

When the used ERW tube mills is used to make welded pipes, it is necessary to rely on the control of the squeeze roller to judge the quality of the welded pipe to be qualified. Therefore, the control of the squeeze roller is very important. There are many ways to control the squeeze roll, "two top rolls, two side vertical rolls and one bottom roll" is one of the squeeze roll methods.

 

Used ERW tube mills

 

The "two top rolls, two side vertical rolls and one bottom roll" five-roller extrusion method is mostly used for units above 325 of the used ERW tube mills. The two top rolls and the two side vertical rolls can be adjusted independently, and the two top rolls are effectively bonded to the steel. The belt edge can form a good extrusion force and effectively control the steel belt edge. This method is mostly used for centerline forming.

 

Used ERW tube mills

 

The disadvantage is that due to mechanical structural considerations and restrictions, the diameter of the upper two top rollers cannot be effectively reduced (when the size is below 325, it is usually equivalent to the diameter of the side vertical roller, when the size is greater than 325, the ratio is relatively appropriate). The bonding line with the steel belt is too long, and it is inevitable to bypass the high-frequency current through the upper top roller structurally.

 

The above-mentioned 4-roll type and 5-roll type will also have the problem similar to the “two on one side” mentioned in the previous article, and the problem will be more serious because the two upper rollers are coordinated up and down through the synchronization mechanism after the initial adjustment. The consistency of the adjustment or the unevenness of the edge caused by the forming of the steel belt edge needs to be overcome here, so the top roller of one side will be adjusted artificially to adapt to the forming defect of the steel belt edge to ensure the basic welding conditions . Therefore, whether the downward pressure given by the two upper rollers to the two sides is symmetrical, whether the center line is consistent with the side rollers, etc., will cause the aforementioned asymmetry in metallography. The pre-bending and forming defects of the part, the amount of pressure is different, which increases the probability of defects after welding. Therefore, the equipment processing accuracy or assembly accuracy of the production line equipment will directly lead to the high or low probability of welding defects. However, such welding defects cannot be found online, which will cause huge product waste.

 

Introduce you to 5 ways to adjust the squeeze roller of the used ERW tube mills. The specific method should be operated according to the actual situation. Please pay attention to safety and do not try it. If you need used welded pipe equipments, please contact us. You only need to inform us of your pipe-making needs, and our company will provide you with used welded pipe equipments that really suits your needs.

关键词:

More News

Analyzing the roll life of a used ERW tube mill
Analyzing the roll life of a used ERW tube mill
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Detail
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
How to extend the service life of high frequency welded pipe equipment
How to extend the service life of high frequency welded pipe equipment
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Detail
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Detail
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Welding and rolling bottom line and sizing rolling bottom line in high frequency welded pipe machine
Welding and rolling bottom line and sizing rolling bottom line in high frequency welded pipe machine
The rolling line of high frequency welded pipe machine is all rolls on the welded pipe unit, including leveling rolls, forming flat rolls, guide rolls, squeeze rolls, deburring idlers, calendering rolls, sizing rolls, straightening rolls and other rolls. It is also the reference line for the installation and adjustment of related auxiliary equipment such as uncoilers, spiral loopers, flying saws, conveyor rollers, etc. It is the general term for the rolling bottom line and rolling center line, just like the human body. The spine plays a pivotal role in all process parameters of welded pipe production.
Detail
The rolling line of high frequency welded pipe machine is all rolls on the welded pipe unit, including leveling rolls, forming flat rolls, guide rolls, squeeze rolls, deburring idlers, calendering rolls, sizing rolls, straightening rolls and other rolls. It is also the reference line for the installation and adjustment of related auxiliary equipment such as uncoilers, spiral loopers, flying saws, conveyor rollers, etc. It is the general term for the rolling bottom line and rolling center line, just like the human body. The spine plays a pivotal role in all process parameters of welded pipe production.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn