MENU

/
/
The characteristics and advantages and disadvantages of the two welding methods of high frequency welded pipe equipment

The characteristics and advantages and disadvantages of the two welding methods of high frequency welded pipe equipment

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-10-14 11:30
  • Pvs:

【概要描述】In the production process of high frequency welded pipe equipment, there are two welding methods: contact welding and induction welding.

The characteristics and advantages and disadvantages of the two welding methods of high frequency welded pipe equipment

【概要描述】In the production process of high frequency welded pipe equipment, there are two welding methods: contact welding and induction welding.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-10-14 11:30
  • Pvs:
Detail

In the production process of high frequency welded pipe equipment, there are two welding methods: contact welding and induction welding.

 

High frequency welded pipe equipment

 

1. Contact welding

Contact welding is a kind of copper electrode contacting the two sides of the steel pipe to be welded, and the induced current penetration is good. The two effects of high-frequency current (proximity effect and skin effect) are maximized by the direct contact between the copper electrode and the steel plate. Utilization, so the welding efficiency of contact welding is higher and the power consumption is lower. It is widely used in the production of high-speed and low-precision pipes, and contact welding is generally required when producing extremely thick steel pipes with high frequency welded pipe equipment.

 

Compared with induction welding, contact welding has two disadvantages:

①The copper electrode is in direct contact with the steel plate and wears quickly

② Due to the influence of the flatness of the steel plate surface and the straightness of the edges, the current stability of contact welding is poor, and the internal and external burrs of the weld are relatively high. Contact welding is generally not used when welding high-precision and thin-walled pipes.

 

High frequency welded pipe equipment

 

2. Induction welding

In induction welding, an induction coil with one or more turns is sheathed outside the welded steel pipe. The effect of multi-turn is better than single-turn, but it is more difficult to manufacture and install multi-turn induction coils. If the distance between the induction coil and the surface of the steel pipe is small, the efficiency is higher, but it is easy to cause discharge between the induction coil and the pipe. Generally, it is advisable to keep the induction coil from the surface of the steel pipe with a gap of 5-8mm. When using induction welding, because the induction coil is not in contact with the steel plate, there is no wear and the induced current is relatively stable, thus ensuring the stability during welding. The welded steel pipe has good surface quality and the weld seam is flat. For high-precision pipes, induction welding is basically used.

 

Realizing that there are two welding methods in the production process of high frequency welded pipe equipment: contact welding and induction welding, as well as their pros and cons. The corresponding welding method should be carried out according to the type of steel pipe actually produced.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn