Used Pipe Mill Supplier
Influence of the defects of the welded pipe blank of the high frequency welded pipe machine on the quality of the welded pipe (9)
- Sort：Information
- Auth:
- Source:
- Release time：2022-10-10 11:30
- Pvs：
【概要描述】If the high frequency welded pipe machine refers to the chemical composition and mechanical properties of welded tube blanks that require certain inspection methods to be known as invisible defects; then, those defects that can be seen only by vision are called tube blanks. Overt defect.
Influence of the defects of the welded pipe blank of the high frequency welded pipe machine on the quality of the welded pipe (9)
【概要描述】If the high frequency welded pipe machine refers to the chemical composition and mechanical properties of welded tube blanks that require certain inspection methods to be known as invisible defects; then, those defects that can be seen only by vision are called tube blanks. Overt defect.
- Sort：Information
- Auth:
- Source:
- Release time：2022-10-10 11:30
- Pvs：
Detail
If the high frequency welded pipe machine refers to the chemical composition and mechanical properties of welded tube blanks that require certain inspection methods to be known as invisible defects; then, those defects that can be seen only by vision are called tube blanks. Overt defect.
The dominant defects of the welded tube blank of the high frequency welded pipe machine generally include cracked edges, broken edges, sawtooth, pitting, scratches, roll marks, dark spots, edge burrs, sickle bends, wrinkles, waves, edge warping, and points. Layers, warped skins, pinholes, sticky rolls, soft spots, rust, oxide layers, towers, loose rolls, etc. Let me introduce you to the causes of cracked edges and the impact of cracked edge billets on welded pipes.
Alice
The peeling skin refers to the iron sheet on the surface of the tube blank. One end is connected to the tube blank substrate, and the other end is separated from the substrate. The difference between it and delamination is that the local warping is obvious, but the formation mechanism is similar to that of delamination. It belongs to the extreme form of partial delamination, and it is located on the surface and is broken.
The effects of warping on the production of welded pipes are as follows:
(1) It is easy to damage the induction coil or the contact, and the magnetic rod will run out, forcing the machine to stop.
(2) The pressure-bearing capacity of the pipe is reduced.
(3) The sensory organ is not good, and it does not meet the requirements of the surface quality of the welded pipe.
Regarding the effect of the welded pipe blank defect of the high frequency welded pipe machine (9) on the quality of the welded pipe, I hope it can be helpful to you.
关键词：
More News
Analysis of seven key factors affecting the effective power output of second-hand high-frequency welded pipe machines
Time of issue : 2024-08-25
High frequency welded pipe machine is widely used in modern industry, especially in the pipe manufacturing industry. It is highly favored by users for its high efficiency and precision. In order to better understand and master this technology, this article will use the keyword "second-hand welded pipe machine" and combine it with practical applications to analyze the seven key factors of its effective power output.
Firstly, we need to clarify the definition of 'second-hand welded pipe machine'. Second hand welded pipe machine refers to equipment that has been used but has been repaired and debugged before being put back into use. Due to its newer production technology and lower purchasing costs, it has become an ideal choice for many small and medium-sized enterprises. However, understanding the influencing factors of power output issues that arise during use, especially in high-frequency and high-intensity operating environments, is crucial.
1. The aging degree of the equipment itself: The components of the second-hand welding pipe machine will wear and age to varying degrees over time, which directly affects the stability of its power output. The maintenance and regular inspection of equipment can reduce this impact.
2. Operating environment: Factors such as humidity, temperature, and electromagnetic interference also have a significant impact on the operation of second-hand welded pipe machines. Maintaining a good working environment is crucial for the effective power output of equipment.
3. Debugging and Calibration: Before the second-hand welded pipe machine is put back into use, it needs to undergo strict debugging and calibration to ensure that all parameters reach their optimal state. This has a significant impact on the stability and power output of the device.
4. Operational skills: Proficient operational skills are the key to ensuring the efficient operation of second-hand welded pipe machines. Familiar with device characteristics and able to flexibly adjust operating parameters can significantly improve power output efficiency.
5. Power quality: Unstable power supply can cause fluctuations in the power output of second-hand welded pipe machines. The use of high-quality power equipment to ensure stable voltage and current is the foundation for ensuring the normal operation of the equipment.
6. Maintenance: Regular maintenance can effectively extend the service life of second-hand welded pipe machines and help stabilize power output. During maintenance, key parts such as welding joints, cooling systems, and electrical components should be carefully inspected.
7. Load adaptability: The power output of a second-hand welded pipe machine is not only affected by the equipment itself, but also by its matching with the load. Appropriate load distribution and reasonable production scheduling can comprehensively improve the operational efficiency of equipment.
In summary, a comprehensive understanding and mastery of the seven key factors mentioned above can significantly improve the effective power output of second-hand high-frequency welded pipe machines, extend equipment life, and lay a solid foundation for enterprises to save costs and improve production efficiency. Mastering these key points will undoubtedly result in twice the result with half the effort when choosing and using a second-hand welded pipe machine.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
High frequency welded pipe machine is widely used in modern industry, especially in the pipe manufacturing industry. It is highly favored by users for its high efficiency and precision. In order to better understand and master this technology, this article will use the keyword "second-hand welded pipe machine" and combine it with practical applications to analyze the seven key factors of its effective power output.
Firstly, we need to clarify the definition of 'second-hand welded pipe machine'. Second hand welded pipe machine refers to equipment that has been used but has been repaired and debugged before being put back into use. Due to its newer production technology and lower purchasing costs, it has become an ideal choice for many small and medium-sized enterprises. However, understanding the influencing factors of power output issues that arise during use, especially in high-frequency and high-intensity operating environments, is crucial.
1. The aging degree of the equipment itself: The components of the second-hand welding pipe machine will wear and age to varying degrees over time, which directly affects the stability of its power output. The maintenance and regular inspection of equipment can reduce this impact.
2. Operating environment: Factors such as humidity, temperature, and electromagnetic interference also have a significant impact on the operation of second-hand welded pipe machines. Maintaining a good working environment is crucial for the effective power output of equipment.
3. Debugging and Calibration: Before the second-hand welded pipe machine is put back into use, it needs to undergo strict debugging and calibration to ensure that all parameters reach their optimal state. This has a significant impact on the stability and power output of the device.
4. Operational skills: Proficient operational skills are the key to ensuring the efficient operation of second-hand welded pipe machines. Familiar with device characteristics and able to flexibly adjust operating parameters can significantly improve power output efficiency.
5. Power quality: Unstable power supply can cause fluctuations in the power output of second-hand welded pipe machines. The use of high-quality power equipment to ensure stable voltage and current is the foundation for ensuring the normal operation of the equipment.
6. Maintenance: Regular maintenance can effectively extend the service life of second-hand welded pipe machines and help stabilize power output. During maintenance, key parts such as welding joints, cooling systems, and electrical components should be carefully inspected.
7. Load adaptability: The power output of a second-hand welded pipe machine is not only affected by the equipment itself, but also by its matching with the load. Appropriate load distribution and reasonable production scheduling can comprehensively improve the operational efficiency of equipment.
In summary, a comprehensive understanding and mastery of the seven key factors mentioned above can significantly improve the effective power output of second-hand high-frequency welded pipe machines, extend equipment life, and lay a solid foundation for enterprises to save costs and improve production efficiency. Mastering these key points will undoubtedly result in twice the result with half the effort when choosing and using a second-hand welded pipe machine.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
Analysis of the problem of non squareness in the adjustment of square and rectangular tubes and the method of correcting vertical rollers
Time of issue : 2024-08-24
Product feature introduction
Economical and cost-effective
Firstly, the price of second-hand welded pipe machines is relatively low, which is their most intuitive advantage. For small and medium-sized enterprises, purchasing second-hand equipment can effectively reduce initial investment costs while ensuring the basic functions and production efficiency of the equipment. This makes second-hand square tube machines highly competitive and cost-effective in the market.
Multi functional and easy to maintain
Another major selling point of second-hand welded pipe machines is their versatility. After appropriate adjustments and maintenance, these machines can produce steel pipes of different specifications and shapes to meet diverse market demands. In addition, the maintenance cost of second-hand equipment is usually lower because at the time of purchase, suppliers often provide detailed usage records and maintenance guidelines for the equipment, making it easier for users to perform daily maintenance and repair minor faults.
The issue of 'non square' in the adjustment process
In the process of using a second-hand square tube machine to produce square and rectangular tubes, a common problem is the phenomenon of "square and rectangular tubes not being square". Specifically, this means that the produced square or rectangular pipes have uneven edges, angles, or lengths on each side, which can affect the quality and aesthetics of the product. The main reasons for this problem are improper machine tool parameter settings, roller wear, and differences in material quality.
Correction method of vertical roller
In order to solve the problem of "non square", the use of standing rollers is particularly important. Vertical roller is a tool used to adjust the shape of pipes. By setting the pressure and position of the vertical roller reasonably, the formed square tube can be calibrated to meet the standard requirements in terms of appearance. In the specific operation, the staff need to gradually adjust the angle and force of the vertical roller according to the actual deviation of the square tube, until the various dimensions of the square tube meet the standards.
Application scenarios and instance analysis
The second-hand welded pipe machine is not only suitable for standardized production, but also meets personalized customization needs. Taking construction sites and pipeline installation projects as examples, these fields often require steel pipes of different sizes and shapes. By adjusting the vertical rollers, the second-hand welded pipe machine can quickly produce square and rectangular pipes that meet specific requirements, greatly improving production efficiency and product quality.
Overall, second-hand square tube machines have become an ideal choice in the market due to their affordability, versatility, and ease of maintenance. By setting up and using vertical rollers reasonably, it is possible to effectively address the issue of "non square" in production and ensure product quality. These unique selling points not only make second-hand welded pipe machines shine in industrial manufacturing, but also bring significant economic benefits to enterprises.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
Product feature introduction
Economical and cost-effective
Firstly, the price of second-hand welded pipe machines is relatively low, which is their most intuitive advantage. For small and medium-sized enterprises, purchasing second-hand equipment can effectively reduce initial investment costs while ensuring the basic functions and production efficiency of the equipment. This makes second-hand square tube machines highly competitive and cost-effective in the market.
Multi functional and easy to maintain
Another major selling point of second-hand welded pipe machines is their versatility. After appropriate adjustments and maintenance, these machines can produce steel pipes of different specifications and shapes to meet diverse market demands. In addition, the maintenance cost of second-hand equipment is usually lower because at the time of purchase, suppliers often provide detailed usage records and maintenance guidelines for the equipment, making it easier for users to perform daily maintenance and repair minor faults.
The issue of 'non square' in the adjustment process
In the process of using a second-hand square tube machine to produce square and rectangular tubes, a common problem is the phenomenon of "square and rectangular tubes not being square". Specifically, this means that the produced square or rectangular pipes have uneven edges, angles, or lengths on each side, which can affect the quality and aesthetics of the product. The main reasons for this problem are improper machine tool parameter settings, roller wear, and differences in material quality.
Correction method of vertical roller
In order to solve the problem of "non square", the use of standing rollers is particularly important. Vertical roller is a tool used to adjust the shape of pipes. By setting the pressure and position of the vertical roller reasonably, the formed square tube can be calibrated to meet the standard requirements in terms of appearance. In the specific operation, the staff need to gradually adjust the angle and force of the vertical roller according to the actual deviation of the square tube, until the various dimensions of the square tube meet the standards.
Application scenarios and instance analysis
The second-hand welded pipe machine is not only suitable for standardized production, but also meets personalized customization needs. Taking construction sites and pipeline installation projects as examples, these fields often require steel pipes of different sizes and shapes. By adjusting the vertical rollers, the second-hand welded pipe machine can quickly produce square and rectangular pipes that meet specific requirements, greatly improving production efficiency and product quality.
Overall, second-hand square tube machines have become an ideal choice in the market due to their affordability, versatility, and ease of maintenance. By setting up and using vertical rollers reasonably, it is possible to effectively address the issue of "non square" in production and ensure product quality. These unique selling points not only make second-hand welded pipe machines shine in industrial manufacturing, but also bring significant economic benefits to enterprises.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier：www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier（Please click the link→) :second-hand pipe mill
Analysis of the problem of non squareness in the adjustment of square and rectangular tubes by second-hand square tube machines and the method of correcting vertical rollers
Innovation of intelligent heat treatment for welds: detailed explanation of online quenching+tempering (Q+T) technology
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province
Recommendation
Online Inquiry
底部留言
描述：
LINK
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Category brief summary:
Contact Us
Tel (wechat): 13336487288
Wechat：+86 13336487288
WhatsApp:+86 13336487288
Email: zty@usedpipemill.com
Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province
