MENU

/
/
How to determine the main size of the guide ring of the high frequency welded pipe machine

How to determine the main size of the guide ring of the high frequency welded pipe machine

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-07-24 11:30
  • Pvs:

【概要描述】The thickness of the guide ring is the main factor that determines the size of the opening angle of the high frequency welded pipe machine. The thickness of the guide ring of the commonly used unit is shown in the table below.

How to determine the main size of the guide ring of the high frequency welded pipe machine

【概要描述】The thickness of the guide ring is the main factor that determines the size of the opening angle of the high frequency welded pipe machine. The thickness of the guide ring of the commonly used unit is shown in the table below.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-07-24 11:30
  • Pvs:
Detail

The thickness of the guide ring is the main factor that determines the size of the opening angle of the high frequency welded pipe machine. The thickness of the guide ring of the commonly used unit is shown in the table below.

 

High frequency welded pipe machine

 

The main basis for the determination of the guide ring is to ensure that the welding opening angle of the high frequency welded pipe machine is between 2°and 6°, and the thickness of the new guide ring corresponds to about 6°. With the occurrence of wear, the opening angle gradually becomes smaller; when the thickness After the wear exceeds 1/2 of its wear, you should consider replacing the guide ring.

 

The bevel angle of the guide ring is related to the width of the tube blank, the forming allowance, and the thickness of the guide ring. See formula:

 

High frequency welded pipe machine

 

The addition of 2°to 5°in brackets is to ensure that the guide ring is in contact with the outer edge of the forming tube first, so as not to damage the inner edge of the tube blank.

 

The ideal contact state between the guide ring and the tube blank should be that the thickness of the tube blank just fits the slope of the guide ring. When the ideal contact state cannot be achieved in actual operation, the inner edge of the tube blank should be avoided to ensure that the guide ring is in contact with the outer edge of the forming tube.

If the guide ring contacts the inner circle edge of the forming tube earlier, it will accelerate the wear of the guide ring and crush the inner circle edge of the tube blank.

 

Outer diameter of guide ring:

 

High frequency welded pipe machine

 

The outer diameter of the guide ring is too small, and the ring is easy to roll to the edge of the tube blank, causing the edge of the formed tube blank to be curled;

If the outer diameter of the guide ring is too large, it is difficult to penetrate the magnetic rod, and it is not economical.

The thin-walled tube takes the larger value.

Thick-walled pipes take the smaller value.

 

The above is to determine the main dimensions of the guide ring of the high frequency welded pipe machine, and also to ensure the quality of the welded pipe forming and weld repair quality when the high frequency welded pipe machine produces welded pipes, so as to produce standard welded pipes.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn