Used Pipe Mill Supplier

Phone:+86-13336487288
Tel:+86-0757-26390113

zty@usedpipemill.com

中文版



Home
Used Welded Pipe Machine 
ERW pipe tube mill Directly Forming To Square pipe Mill Cold roll forming Machine Used Spiral Pipe Mills Forming roll Used Stainless Steel Tube Mill Tube Mill Auxiliary Equipment Consumables / accessories
Steel slitting machine 
Slitting Equipment Model Slitting Machine Application Auxiliary Equipment Part
Application cases 
Building pipe Furniture pipe Guardrail tube Fluid pipe Automobile tube Threading pipe Water gas pipe Galvanized square tube ERW pipe API Pipe Hot roll slitting
Custom Made
Information 
Information Customer Evaluation Solution Q&A
About us 
About Us Contact Us Hiring Talent

Homepage

Information

How to adjust the opening angle of used welded pipe machine

Sort：Information
Auth:
Source:
Release time：2022-09-21 11:30
Pvs：

【概要描述】When adjusting the pipe opening angle of used welded pipe machine, the following 4 basic methods should be followed.

How to adjust the opening angle of used welded pipe machine

【概要描述】When adjusting the pipe opening angle of used welded pipe machine, the following 4 basic methods should be followed.

Sort：Information
Auth:
Source:
Release time：2022-09-21 11:30
Pvs：

Detail

When adjusting the pipe opening angle of used welded pipe machine, the following 4 basic methods should be followed.

(1) Wall thickness method. It means that the opening angle should be reduced as much as possible when producing thick-walled pipes, and the opening angle should be appropriately increased when using used welded pipe machine to produce thin-walled pipes.

(2) The natural way. That is, as the guide ring and the hole pattern are naturally worn out, the guide roller is pressed down in stages, so that the opening angle will decrease accordingly; after the new guide ring is replaced, the opening angle should be restored to the original state.

Used welded pipe machine

(3) Micro-deformation method. In theory, the guide roller does not undertake the task of deformation; however, starting from the actual need to stabilize the opening angle, it is necessary to allow the guide roller to undertake the slight deformation limited to the control of springback.

(4) Efficiency method. In order to improve the power utilization efficiency and production efficiency, the opening angle must be adjusted as small as possible when the process conditions permit.

The four basic ways to adjust the opening angle of the pipe made by used welded pipe machine must be adjusted according to the actual situation of the opening angle.

关键词：

Previous: About the influence of the defects of the welded pipe blank of the high frequency welded pipe machine on the quality of the welded pipe (3)

Next: Correct selection of induction coils for high frequency welded pipe equipment

Previous: About the influence of the defects of the welded pipe blank of the high frequency welded pipe machine on the quality of the welded pipe (3)

Next: Correct selection of induction coils for high frequency welded pipe equipment

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)

Time of issue : 2023-06-09

Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .

Detail

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)

Time of issue : 2023-06-06

Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).

Detail

Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).

Solution for thick wall tube forming of used round pipe to square pipe machines（2）

Time of issue : 2023-06-03

In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.

Detail

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)

Time of issue : 2023-05-31

Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).

Detail

Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).

Contact information

Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province