MENU

/
/
How to adjust the extrusion roll "two top rolls and two side vertical rolls" of the used ERW tube mills

How to adjust the extrusion roll "two top rolls and two side vertical rolls" of the used ERW tube mills

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-11-25 11:30
  • Pvs:

【概要描述】When the used ERW tube mills is used to make welded pipes, it is necessary to rely on the control of the squeeze roller to judge the quality of the welded pipe to be qualified. Therefore, the control of the squeeze roller is very important. There are many ways to control the squeeze roll. "Two top rolls and two side vertical rolls" is one of the squeeze roll methods.

How to adjust the extrusion roll "two top rolls and two side vertical rolls" of the used ERW tube mills

【概要描述】When the used ERW tube mills is used to make welded pipes, it is necessary to rely on the control of the squeeze roller to judge the quality of the welded pipe to be qualified. Therefore, the control of the squeeze roller is very important. There are many ways to control the squeeze roll. "Two top rolls and two side vertical rolls" is one of the squeeze roll methods.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-11-25 11:30
  • Pvs:
Detail

When the used ERW tube mills is used to make welded pipes, it is necessary to rely on the control of the squeeze roller to judge the quality of the welded pipe to be qualified. Therefore, the control of the squeeze roller is very important. There are many ways to control the squeeze roll. "Two top rolls and two side vertical rolls" is one of the squeeze roll methods.

 

Used ERW tube mills

 

The "two top rollers and two side vertical rollers" four-roller extrusion method can be said to be the first choice for used ERW tube mills at present for units above 114. The two top rollers and the two side vertical rollers can be adjusted independently, and the two top rollers are effective. Fit the edges of the steel strip to form a good extrusion force and effectively control the edges of the steel strip. For large-wall steel pipes, this method can fully reflect its advantages. The two-side vertical rolls cover less than 150 degrees, which effectively reduces the diameter of the squeeze rolls, shortens the length of the Vee, and improves the welding efficiency. It is an ideal form of welding and extrusion.

 

Used ERW tube mills

 

Used ERW tube mills

 

The disadvantage is that due to mechanical structural considerations and restrictions, the diameter of the upper two top rollers cannot be effectively reduced (usually equivalent to the diameter of the side vertical roller), and the bonding line with the steel strip is too long. High-frequency current is inevitable.

 

The above is the method of adjusting the squeeze roll "two top rolls and two side vertical rolls" of the used ERW tube mills, and the method ⑤ "two top rolls, two side vertical rolls and one bottom roll" will be introduced in the next issue. If you need it, you can pay attention to the method in the next issue. At the same time, if you need used welded pipe equipment, please contact us. You only need to inform us of your pipe-making needs, and our company will provide you with used welded pipe equipments that really suits your needs.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Detail
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn