Four categories of welded pipe blanks for used high frequency welded pipe equipment (1)
- Sort:Information
- Auth:
- Source:
- Release time:2023-04-02 11:30
- Pvs:
【概要描述】Welded pipe blank is the raw material of used high frequency welded pipe equipment to make welded pipe. Its mechanical properties and chemical composition have a profound impact on the quality of welded pipe, and its width is the first factor that determines the strength of the weld. We usually say that the width of the welded pipe blank is suitable, which refers to the width of the given thickness; the determination of the width is restricted by many factors.
Four categories of welded pipe blanks for used high frequency welded pipe equipment (1)
【概要描述】Welded pipe blank is the raw material of used high frequency welded pipe equipment to make welded pipe. Its mechanical properties and chemical composition have a profound impact on the quality of welded pipe, and its width is the first factor that determines the strength of the weld. We usually say that the width of the welded pipe blank is suitable, which refers to the width of the given thickness; the determination of the width is restricted by many factors.
- Sort:Information
- Auth:
- Source:
- Release time:2023-04-02 11:30
- Pvs:
Welded pipe blank is the raw material of used high frequency welded pipe equipment to make welded pipe. Its mechanical properties and chemical composition have a profound impact on the quality of welded pipe, and its width is the first factor that determines the strength of the weld. We usually say that the width of the welded pipe blank is suitable, which refers to the width of the given thickness; the determination of the width is restricted by many factors.
This article discusses various calculation methods of tube blank width, and points out the commonalities and differences of various calculation methods and their applicable conditions. At the same time, the defects of the welded pipe blanks are divided into two categories: dominant and recessive, and the adverse effects of the defects of the welded pipe blanks on the production of welded pipes are analyzed.
Classification of welded pipe blanks:
The welded pipe blanks of used high frequency welded pipe equipment can be divided into four categories according to the steel type, the temperature when rolling the pipe blank, the width of the source of the welded pipe blank and the edge state of the welded pipe blank. The following introduces the welded pipe blanks classified by steel type.
Classification by steel grade
Q series welded pipe blanks: Q series welded pipe blanks are also known as ordinary carbon steel welded pipe blanks. To use ordinary carbon steel as welded pipe blank, two points need to be explained:
(1) Since ordinary carbon structural steel only has strict regulations on the chemical composition of the steel, and does not require mechanical properties, the high-frequency longitudinally welded pipes produced by ordinary carbon structural steel for used high frequency welded pipe equipment are in the delivery process. In theory, the mechanical properties cannot be guaranteed.
(2) The standard is only a minimum requirement, due to the needs of market competition, and with the continuous improvement and improvement of steelmaking level, rolling technology, especially cold rolling technology and its related annealing process, finishing process, and tension leveling process, The mechanical properties of Q series welded pipe blanks have been improved a lot, and some are comparable to high-quality carbon structural steel. The mechanical properties of cold-rolled bright tubes produced by Q series cold-rolled bright annealed steel strips are not much different from those of high-quality carbon structural steel.
High-quality steel series welded pipe blanks
(1) High-quality carbon structural steel must not only ensure the chemical composition of the tube blank, but also ensure the mechanical properties of the tube blank. Therefore, the welded pipes made of high-quality carbon structural steel pipe billets are at least guaranteed in terms of mechanical properties.
(2) Affected by the Bauschinger effect, after the welded pipe blank is deformed by forming, welding extrusion and plastic deformation, indicators such as elongation and shrinkage rate will decrease, while yield strength and tensile strength will slightly decrease. rise. On the one hand, it reminds us to pay attention to the performance indicators when purchasing high-quality steel welded pipe blanks; The formed tube blank is partially stressed to prevent the Bauschinger effect from being strengthened. The Bauschinger effect manifests itself in all steel deformations, differing in degree.
Tip: Bauschinger effect: a metal that has undergone plastic deformation in a certain direction, when it is deformed in the opposite direction, its yield strength decreases significantly compared with the stress-strain in the original pre-strain direction. This phenomenon was first discovered by the German Bauschinger in 1886, and was named after him, abbreviated as BE (Bauschinger effect). This effect adversely affects the cold plastic deformation, alignment, dimensional stability and service performance of the material, adding a variable to be predicted. The research results of the Bauschinger effect given in the traditional literature usually refer to the results under the condition of axial tension and compression test, and the microscopic stress inside the material is usually the microscopic stress within the grain size range. The explanation is also based on this. However, for plastic bending from plate to tube, considerable macroscopic residual stresses are introduced, which can have an additional significant effect on the Bauschinger effect.
The method to eliminate the Bauschinger effect: perform large plastic deformation in advance, or anneal the metal material at the recovery or recrystallization temperature before the second reverse force, such as steel above 400~500℃, copper alloy At 250~270℃.
Low alloy steel series welded pipe blanks
Low alloy steel welded pipe blanks must not only ensure the chemical composition of the pipe blanks, but also must ensure high yield resistance, tensile strength and certain toughness. Mainly used to produce high strength. Impact-resistant and wear-resistant pipes, such as oil transportation pipes, coal slurry transportation pipes, transmission shaft pipes, long-span steel structure pipes, high-strength structural pipes, etc. The biggest advantage of using low-alloy steel welded pipes is the high cost performance. It can reduce the weight of meters and reduce the self-weight of components through strength replacement without reducing the strength of the components, which is particularly important for large-span steel structures.
Micro-alloyed steel series tube blank
This type of tube blank is a welded tube blank specially developed to meet the needs of some specific customers or specific uses. Mainly relying on the platform of low-alloy structural steel and high-quality structural steel, by adding some trace metals or non-metals, the tube blank and welded pipe have some special functions.
The above is one of the "steel grades" about the welded pipe blanks of used high frequency welded pipe equipment. From the perspective of steel grades, it can be divided into Q series welded pipe blanks, high-quality steel series welded pipe blanks, low alloy steel series welded pipe blanks, micro-alloyed steel pipe blanks Steel series tube blanks.
Part of the content of this site comes from the Internet, this site only provides information storage, the copyright belongs to the original author, does not bear relevant legal responsibility, does not represent the views and positions of this site, if there is any infringement, please contact to delete.
More News

Time of issue : 2025-02-11
1. The characteristics of high-precision steel pipe
High dimensional accuracy: small outer diameter, wall thickness tolerance (usually up to ±0.05mm), low ellipticity.
Excellent surface quality: smooth weld without burrs, surface finish Ra≤0.8μm.
Stable mechanical properties: weld strength close to the base material, uniform compressive/tensile properties.
Applicable materials: stainless steel (304/316L), carbon steel, alloy steel (such as API series), etc.
2. Core production process
(1) Type of pipe welding machine
High-frequency welding (HFW) : high efficiency, suitable for medium thin wall pipe (Φ10~Φ600mm), need to cooperate with precision forming unit.
Laser welding: small heat affected zone, narrow weld (0.1~0.3mm), suitable for ultra-thin walls (such as 0.3mm) or special alloys.
TIG welding: For high alloy steel or thick wall pipe, higher weld purity.
(2) Key process links
Forming process: multi-roll continuous cold forming, dynamic adjustment of roll parameters to compensate for rebound.
Welding control:
High frequency welding: precise control of current frequency (100~400kHz) and extrusion amount.
Laser welding: focus position accuracy ±0.05mm, real-time depth monitoring (such as CCD vision).
Online detection:
Eddy current inspection (ET) : Detection of surface cracks.
Ultrasonic inspection (UT) : detection of internal defects (sensitivity Φ0.5mm equivalent flat hole).
Laser caliper: Outer diameter closed loop control (accuracy ±0.01mm).
3. Post-processing technology
Heat treatment: bright annealing (hydrogen nitrogen protection atmosphere) to eliminate stress, hardness fluctuation ≤3HRC.
Straightening: multi-roll precision straightening, straightness ≤0.5mm/m.
Surface treatment:
Electrolytic polishing (EP) : For medical/food grade stainless steel tubes, Ra up to 0.2μm.
Coating: hot dip galvanizing (zinc layer ≥80μm) or electroless nickel plating (uniform thickness ±2μm).
4. Typical application areas
Automobile manufacturing: fuel injection pipe (tolerance ±0.03mm), hydraulic pipe.
Semiconductor equipment: Ultra-high clean gas delivery pipe (inner wall EP treatment, particle ≤Class 5).
Medical instruments: endoscopic catheter (Φ1~5mm, wall thickness 0.1mm).
Energy industry: Instrument tubes for nuclear power plants (SA213-TP347H material, intergranular corrosion test passed).
5. Quality control standards
International standard:
ASTM A269 (Universal Seamless and Welded Austenitic Stainless Steel Pipe)
EN 10305-4 (Precision welded pipes for hydraulic systems)
Industry certification: ISO 9001, PED 2014/68/EU (Pressure Equipment Directive).
6. Technological trends
Intelligent production: AI algorithm optimizes welding parameters, and the yield is increased to more than 99.5%.
Composite process: laser + arc composite welding, both efficiency and quality (speed increased by 30%).
Green manufacturing: low energy high frequency power supply (efficiency ≥90%), waste acid recovery ≥95%.
Through the above process optimization and strict quality control, the high-precision steel pipe produced by the pipe welding machine can meet the demanding requirements of size, performance and reliability in high-end industrial fields. In actual production, the process route needs to be customized according to the material characteristics and uses, for example, medical tubes need to undergo additional passivation treatment and biocompatibility testing.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill
1. The characteristics of high-precision steel pipe
High dimensional accuracy: small outer diameter, wall thickness tolerance (usually up to ±0.05mm), low ellipticity.
Excellent surface quality: smooth weld without burrs, surface finish Ra≤0.8μm.
Stable mechanical properties: weld strength close to the base material, uniform compressive/tensile properties.
Applicable materials: stainless steel (304/316L), carbon steel, alloy steel (such as API series), etc.
2. Core production process
(1) Type of pipe welding machine
High-frequency welding (HFW) : high efficiency, suitable for medium thin wall pipe (Φ10~Φ600mm), need to cooperate with precision forming unit.
Laser welding: small heat affected zone, narrow weld (0.1~0.3mm), suitable for ultra-thin walls (such as 0.3mm) or special alloys.
TIG welding: For high alloy steel or thick wall pipe, higher weld purity.
(2) Key process links
Forming process: multi-roll continuous cold forming, dynamic adjustment of roll parameters to compensate for rebound.
Welding control:
High frequency welding: precise control of current frequency (100~400kHz) and extrusion amount.
Laser welding: focus position accuracy ±0.05mm, real-time depth monitoring (such as CCD vision).
Online detection:
Eddy current inspection (ET) : Detection of surface cracks.
Ultrasonic inspection (UT) : detection of internal defects (sensitivity Φ0.5mm equivalent flat hole).
Laser caliper: Outer diameter closed loop control (accuracy ±0.01mm).
3. Post-processing technology
Heat treatment: bright annealing (hydrogen nitrogen protection atmosphere) to eliminate stress, hardness fluctuation ≤3HRC.
Straightening: multi-roll precision straightening, straightness ≤0.5mm/m.
Surface treatment:
Electrolytic polishing (EP) : For medical/food grade stainless steel tubes, Ra up to 0.2μm.
Coating: hot dip galvanizing (zinc layer ≥80μm) or electroless nickel plating (uniform thickness ±2μm).
4. Typical application areas
Automobile manufacturing: fuel injection pipe (tolerance ±0.03mm), hydraulic pipe.
Semiconductor equipment: Ultra-high clean gas delivery pipe (inner wall EP treatment, particle ≤Class 5).
Medical instruments: endoscopic catheter (Φ1~5mm, wall thickness 0.1mm).
Energy industry: Instrument tubes for nuclear power plants (SA213-TP347H material, intergranular corrosion test passed).
5. Quality control standards
International standard:
ASTM A269 (Universal Seamless and Welded Austenitic Stainless Steel Pipe)
EN 10305-4 (Precision welded pipes for hydraulic systems)
Industry certification: ISO 9001, PED 2014/68/EU (Pressure Equipment Directive).
6. Technological trends
Intelligent production: AI algorithm optimizes welding parameters, and the yield is increased to more than 99.5%.
Composite process: laser + arc composite welding, both efficiency and quality (speed increased by 30%).
Green manufacturing: low energy high frequency power supply (efficiency ≥90%), waste acid recovery ≥95%.
Through the above process optimization and strict quality control, the high-precision steel pipe produced by the pipe welding machine can meet the demanding requirements of size, performance and reliability in high-end industrial fields. In actual production, the process route needs to be customized according to the material characteristics and uses, for example, medical tubes need to undergo additional passivation treatment and biocompatibility testing.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill

Time of issue : 2025-02-08
1.The role of pipe welding machine in the manufacture of automobile frame
Pipe production: The welding pipe machine is used to manufacture high-precision welded steel pipes, which constitute the longitudinal beams, beams, anti-collision beams and other key components of the automobile frame. High frequency welding (HFW) or laser welding technology can produce steel pipes with uniform wall thickness and strength of more than 800MPa to meet the needs of lightweight.
Customized processing: Through flexible forming technology, the welding machine can produce special-shaped cross section pipes (such as rectangular, trapezoidal), adapt to the topology optimization design of different models of frames, improve space utilization and impact energy absorption efficiency.
2.The core requirements of the welding pipe process for automobile frames
Material properties: DP600/DP800 duplex steel or 22MnB5 thermoforming steel should be used, and online heat treatment (such as induction annealing) should be carried out after welding to ensure the microstructure consistency between the weld zone and the base material and avoid HAZ (heat affected zone) softening.
Dimensional accuracy: Diameter tolerance should be controlled within ±0.2mm, ellipticity ≤0.5%, to ensure the matching accuracy of the assembly and stamping parts (clearance <0.5mm).
3.Key technology breakthrough point
Laser-MAG composite welding: the penetration depth can reach 8mm, the welding speed is increased to 6m/min, the heat input is reduced by 30%, and the welding deformation of the frame is significantly reduced (≤1.5mm/m).
Online quality monitoring: high-speed CCD vision system (sampling rate 2000fps) with eddy current detection, to achieve real-time detection of weld defects, miss rate <0.01%.
4.Cost-performance balance
Compared with the stamping and welding structure, the welded pipe frame can reduce the weight by 15-20%, the material utilization rate is increased to 95%, and the manufacturing cost of the bicycle is reduced by about 1200 yuan. However, it is necessary to increase the investment in roller forming molds (about 2 million yuan/set).
5.Industry Application Cases
- An independent brand pure level station adopts 3D variable cross-section welded pipe subframe, with torsional rigidity increased to 27000Nm/°, 40% higher than the traditional structure, and the battery pack space utilization increased by 12%.
Conclusion
The penetration rate of welded pipe technology in the field of automotive frames is growing at a rate of 8% per year, and future development directions include:
Intelligent welded pipe system (digital twin model real-time control molding parameters)
Magnesium alloy /CFRP composite pipe welding process
Topological optimization driven continuous forming technology for variable thickness pipes
It is recommended to pay attention to the update of the ISO 15614 standard and the latest certification requirements for automotive welded pipe processes in ASME BPVC Section IX to ensure technical compliance.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill
1.The role of pipe welding machine in the manufacture of automobile frame
Pipe production: The welding pipe machine is used to manufacture high-precision welded steel pipes, which constitute the longitudinal beams, beams, anti-collision beams and other key components of the automobile frame. High frequency welding (HFW) or laser welding technology can produce steel pipes with uniform wall thickness and strength of more than 800MPa to meet the needs of lightweight.
Customized processing: Through flexible forming technology, the welding machine can produce special-shaped cross section pipes (such as rectangular, trapezoidal), adapt to the topology optimization design of different models of frames, improve space utilization and impact energy absorption efficiency.
2.The core requirements of the welding pipe process for automobile frames
Material properties: DP600/DP800 duplex steel or 22MnB5 thermoforming steel should be used, and online heat treatment (such as induction annealing) should be carried out after welding to ensure the microstructure consistency between the weld zone and the base material and avoid HAZ (heat affected zone) softening.
Dimensional accuracy: Diameter tolerance should be controlled within ±0.2mm, ellipticity ≤0.5%, to ensure the matching accuracy of the assembly and stamping parts (clearance <0.5mm).
3.Key technology breakthrough point
Laser-MAG composite welding: the penetration depth can reach 8mm, the welding speed is increased to 6m/min, the heat input is reduced by 30%, and the welding deformation of the frame is significantly reduced (≤1.5mm/m).
Online quality monitoring: high-speed CCD vision system (sampling rate 2000fps) with eddy current detection, to achieve real-time detection of weld defects, miss rate <0.01%.
4.Cost-performance balance
Compared with the stamping and welding structure, the welded pipe frame can reduce the weight by 15-20%, the material utilization rate is increased to 95%, and the manufacturing cost of the bicycle is reduced by about 1200 yuan. However, it is necessary to increase the investment in roller forming molds (about 2 million yuan/set).
5.Industry Application Cases
- An independent brand pure level station adopts 3D variable cross-section welded pipe subframe, with torsional rigidity increased to 27000Nm/°, 40% higher than the traditional structure, and the battery pack space utilization increased by 12%.
Conclusion
The penetration rate of welded pipe technology in the field of automotive frames is growing at a rate of 8% per year, and future development directions include:
Intelligent welded pipe system (digital twin model real-time control molding parameters)
Magnesium alloy /CFRP composite pipe welding process
Topological optimization driven continuous forming technology for variable thickness pipes
It is recommended to pay attention to the update of the ISO 15614 standard and the latest certification requirements for automotive welded pipe processes in ASME BPVC Section IX to ensure technical compliance.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill

Time of issue : 2025-02-07
89 The working principle of the pipe welding machine 89 The pipe welding machine uncoils the steel strip, feeds and welds it into a round steel pipe, and then cools, straightens and cuts the steel pipe to the required length. The main steps include:
1. Uncoiling: Unroll the steel strip from the drum and level it through the straightener.
2. Forming: The steel strip is rolled into a tube shape through a series of roller wheels.
3. Welding: high frequency current is used to heat the joint of the steel strip, so as to weld the steel pipe.
4. Cooling: The welded steel pipe is cooled by cooling equipment.
5. Straightening and cutting: Finally, straighten and cut the steel pipe to the required length.
The main steel pipe used in the highway fence needs to have a certain strength and impact resistance, but also corrosion resistance. Specific features include:
1. High strength: the steel pipe must be able to withstand the impact to ensure the safety of the highway.
2. Corrosion resistance: steel pipes are usually galvanized to enhance their corrosion resistance and adapt to harsh outdoor environments.
3. Standard size: The steel pipe produced generally has strict size requirements to ensure the stability of the fixed connection of each fence.
The steel pipe produced by the 89 pipe welding machine plays a skeleton role in the highway fence, and its application is reflected in:
1. Guardrail: installed on both sides of the highway or in the middle, to prevent the vehicle from losing control of the road, to protect the safety of the driver.
2. Isolation belt: Set isolation belts between lanes in different directions to prevent vehicles from crossing lanes and reduce the incidence of accidents.
3. Sound barrier: The use of steel pipe frame to support the sound barrier plate to reduce the impact of road noise on the surrounding environment.
In short, the 89 pipe welding machine plays a key role in the production of steel pipes for highway fences, ensuring the stability, durability and safety of the fences, thus providing a reliable guarantee for the safe operation of the highways.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill
89 The working principle of the pipe welding machine 89 The pipe welding machine uncoils the steel strip, feeds and welds it into a round steel pipe, and then cools, straightens and cuts the steel pipe to the required length. The main steps include:
1. Uncoiling: Unroll the steel strip from the drum and level it through the straightener.
2. Forming: The steel strip is rolled into a tube shape through a series of roller wheels.
3. Welding: high frequency current is used to heat the joint of the steel strip, so as to weld the steel pipe.
4. Cooling: The welded steel pipe is cooled by cooling equipment.
5. Straightening and cutting: Finally, straighten and cut the steel pipe to the required length.
The main steel pipe used in the highway fence needs to have a certain strength and impact resistance, but also corrosion resistance. Specific features include:
1. High strength: the steel pipe must be able to withstand the impact to ensure the safety of the highway.
2. Corrosion resistance: steel pipes are usually galvanized to enhance their corrosion resistance and adapt to harsh outdoor environments.
3. Standard size: The steel pipe produced generally has strict size requirements to ensure the stability of the fixed connection of each fence.
The steel pipe produced by the 89 pipe welding machine plays a skeleton role in the highway fence, and its application is reflected in:
1. Guardrail: installed on both sides of the highway or in the middle, to prevent the vehicle from losing control of the road, to protect the safety of the driver.
2. Isolation belt: Set isolation belts between lanes in different directions to prevent vehicles from crossing lanes and reduce the incidence of accidents.
3. Sound barrier: The use of steel pipe frame to support the sound barrier plate to reduce the impact of road noise on the surrounding environment.
In short, the 89 pipe welding machine plays a key role in the production of steel pipes for highway fences, ensuring the stability, durability and safety of the fences, thus providing a reliable guarantee for the safe operation of the highways.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill

Time of issue : 2025-01-23
1.Supply channels:
Online marketplaces: For example, Taobao, Alibaba, Jingdong and other platforms can search and find used equipment.
Professional used equipment market: Some areas have a special used equipment market, you can view the equipment situation on the spot.
Industry exhibitions: Participate in machinery, manufacturing related exhibitions, sometimes you can find suppliers to provide second-hand equipment opportunities.
Peers and recommendations: Ask peers and friends in the industry to obtain reliable equipment and supplier information.
2.Selection criteria:
Equipment condition: Carefully check the service life, maintenance records and running status of the equipment to ensure that the function is intact.
Brand and model: Choose well-known brands and reliable models, usually the quality is guaranteed, and the after-sales service is relatively perfect.
Price comparison: multiple inquiries to ensure reasonable prices to avoid buying inferior equipment at low prices.
Service and Accessories: Find out if the supplier provides after-sales service and accessories to ensure convenient maintenance in subsequent use.
3.Site inspection:
Equipment operation demonstration: The seller is required to perform equipment operation demonstration to observe the actual operation.
Technical Support: Evaluate the seller's technical support capabilities, including whether to provide installation and commissioning services.
Contract protection: Sign a detailed procurement contract to clarify the responsibilities of both parties, equipment specifications, payment methods, after-sales service and other content.
4.Trial Period:
Trial commitment: Try to strive for a certain trial period in order to find potential problems with the equipment during use.
Troubleshooting: During the trial period, pay close attention to the operation of the equipment, if there is a failure, contact the seller as soon as possible.
Through the above methods, you can better purchase a satisfactory second-hand pipe making machine.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill
1.Supply channels:
Online marketplaces: For example, Taobao, Alibaba, Jingdong and other platforms can search and find used equipment.
Professional used equipment market: Some areas have a special used equipment market, you can view the equipment situation on the spot.
Industry exhibitions: Participate in machinery, manufacturing related exhibitions, sometimes you can find suppliers to provide second-hand equipment opportunities.
Peers and recommendations: Ask peers and friends in the industry to obtain reliable equipment and supplier information.
2.Selection criteria:
Equipment condition: Carefully check the service life, maintenance records and running status of the equipment to ensure that the function is intact.
Brand and model: Choose well-known brands and reliable models, usually the quality is guaranteed, and the after-sales service is relatively perfect.
Price comparison: multiple inquiries to ensure reasonable prices to avoid buying inferior equipment at low prices.
Service and Accessories: Find out if the supplier provides after-sales service and accessories to ensure convenient maintenance in subsequent use.
3.Site inspection:
Equipment operation demonstration: The seller is required to perform equipment operation demonstration to observe the actual operation.
Technical Support: Evaluate the seller's technical support capabilities, including whether to provide installation and commissioning services.
Contract protection: Sign a detailed procurement contract to clarify the responsibilities of both parties, equipment specifications, payment methods, after-sales service and other content.
4.Trial Period:
Trial commitment: Try to strive for a certain trial period in order to find potential problems with the equipment during use.
Troubleshooting: During the trial period, pay close attention to the operation of the equipment, if there is a failure, contact the seller as soon as possible.
Through the above methods, you can better purchase a satisfactory second-hand pipe making machine.
For more information, please pay attention to the website of Jinyujie Mechanical and Electrical Used Pipe Mill Supplier:www.usedpipemill.com
JinYuJie-Used Pipe Mills Supplier(Please click the link→) :second-hand pipe mill
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province
Recommendation
Online Inquiry
LINK
Contact Us
Tel (wechat): 13336487288
Wechat:+86 13336487288
WhatsApp:+86 13336487288
Email: zty@usedpipemill.com
Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province
