MENU

/
/
Factors causing weld quality failures in used roll forming machines—periodic lap welding

Factors causing weld quality failures in used roll forming machines—periodic lap welding

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-09-25 11:30
  • Pvs:

【概要描述】Factors that cause weld quality failures in used roll forming machines include ①lap welding.②cycle lap welding. ③opening. ④bathholes. The following is an introduction to the cycle lap welding, the factor that causes the quality of the weld.

Factors causing weld quality failures in used roll forming machines—periodic lap welding

【概要描述】Factors that cause weld quality failures in used roll forming machines include ①lap welding.②cycle lap welding. ③opening. ④bathholes. The following is an introduction to the cycle lap welding, the factor that causes the quality of the weld.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-09-25 11:30
  • Pvs:
Detail

Factors that cause weld quality failures in used roll forming machines include ①lap welding.②cycle lap welding. ③opening. ④bathholes. The following is an introduction to the cycle lap welding, the factor that causes the quality of the weld.

 

Lap welding is an intermittent appearance, sometimes not, sometimes the length of the lap welding is slightly longer, a few centimeters or even tens of centimeters, and sometimes it is slightly shorter, ranging from one to two centimeters or less. Sometimes lap welding occurs regularly and equidistantly, and sometimes it appears irregularly. For these lap welding phenomena, we collectively refer to them as periodic lap welding. Periodic lap welding in used roll forming machines generally occurs in the middle and late stages of production, mainly due to the following reasons:

 

Used roll forming machines

 

(1) The guide ring is broken. When the closed pass is worn, the normal operation of the tube blank cannot be effectively controlled, and the tube blank can swing back and forth in the pass. At this time, after the guide ring ruptures and there is a gap, the edge of the tube blank will be compressed by the gap of the guide ring during the running process, thereby forming the generation of lap welded pipe. The characteristics of this lap welded pipe are the same length of lap welding cycle, strong regularity, and easier to judge. Generally, as the guide ring rotates after the rupture, the traces of compression can be found.

 

(2) Hole type wear. Mainly refers to the stepped shape at the bottom diameter of the upper roller of the closed hole type, and the stepped shape at the upper edge of the vertical roller hole type of the open hole type.

 

Used roll forming machines

 

When the blank tube slides to the part of the hole-shaped boss when it swings in the hole pattern, the blank tube will be deformed. The edges produce sag marks to form lap welding. Sliding in and out instantly makes the lap welding smaller, and vice versa. The best way to eliminate this kind of overlap welded pipe is to make reasonable adjustments during normal production to make the hole wear uniform and avoid stepped shapes. Once the irregular shape of the arc of the hole is found, it must be replaced in time. In order to completely eliminate the occurrence of lap welding.

 

(3) Foreign matter on the arc surface of the hole. Sometimes on the arc surface of the pass, other metal foreign bodies are adhered for some reason, which will cause the surface of the tube blank to appear indentation scars. When the adhesion position of this foreign body is in the trajectory of the edge of the tube blank , It will cause short and equidistant periodic lap welding. Under normal circumstances, this phenomenon rarely occurs.

 

Used roll forming machines

 

(4) Swing seam. In the later stage of production, the pass wear is more serious, the ability to control the tube blank is gradually reduced, and the center position of each pass has been damaged to varying degrees. Therefore, from forming to welding, the phenomenon of unsteady running of the tube will appear. The lap welding caused by the swing seam is mostly caused by the vertical roller. The flat roller sometimes causes some lap welded pipes, but the probability is smaller in comparison. When inspecting the edge condition of the tube blank, it is also difficult to find any abnormalities and obvious depression defects. The height of the two edges of the tube blank is slightly different until the squeeze roll. At this time, attention should be paid to the shape of the upper edge of the vertical roll pass. If it is ideal, the shrinkage of the vertical roll can be increased to obtain a perfect tube blank edge deformation effect. If the upper edge of the vertical roll pass is not too good In good times, it is necessary to reduce the shrinkage of the vertical roll to prevent undesirable deformation.

 

(5) The bearing is damaged. After the closed-hole bearing is damaged, the smooth running of the tube billet cannot be controlled well, and the phenomenon of wobble seam is prone to occur, and the possibility of lap welding will follow. Especially after the bearing with multiple closed holes is damaged, the lap welding problem will be more serious. Of course, this phenomenon rarely occurs even if it happens. Adjustment will not solve the problem.

 

Due to the above 5 factors, the quality of the welding seam in the used roll forming machines is caused by periodic lap welding. When the welded pipe is made, it is necessary to check whether the used roll forming machines has these problems.

关键词:

More News

How to solve the common problems of used high-frequency welded pipe making machine?
How to solve the common problems of used high-frequency welded pipe making machine?
Used high-frequency welded pipe making machine is a commonly used equipment in the metal pipe processing industry, which mainly uses high-frequency welding technology to weld strip steel into pipes after forming. Because it is cost-effective and easy to operate, it is favored by small and medium-sized enterprises.
Detail
Used high-frequency welded pipe making machine is a commonly used equipment in the metal pipe processing industry, which mainly uses high-frequency welding technology to weld strip steel into pipes after forming. Because it is cost-effective and easy to operate, it is favored by small and medium-sized enterprises.
Five major issues that must be considered before purchasing a second-hand high-frequency welded pipe machine
Five major issues that must be considered before purchasing a second-hand high-frequency welded pipe machine
When looking for a second-hand high-frequency welded pipe machine in the market, it is crucial to understand its product characteristics, which can help you make an informed investment decision. A high quality second-hand high-frequency welded pipe machine should have the following five key characteristics:
Detail
When looking for a second-hand high-frequency welded pipe machine in the market, it is crucial to understand its product characteristics, which can help you make an informed investment decision. A high quality second-hand high-frequency welded pipe machine should have the following five key characteristics:
How to avoid the price-performance trap when choosing a second-hand high-frequency welded pipe machine?
How to avoid the price-performance trap when choosing a second-hand high-frequency welded pipe machine?
When looking for cost-effective production solutions in the market, second-hand high-frequency welded pipe machines have become the choice of many companies.
Detail
When looking for cost-effective production solutions in the market, second-hand high-frequency welded pipe machines have become the choice of many companies.
Maintenance problem: What are the maintenance points of second-hand high-frequency pipe welding machine?
Maintenance problem: What are the maintenance points of second-hand high-frequency pipe welding machine?
Second-hand high-frequency pipe welding machine, as an important equipment in industrial pipe production, can provide stable performance despite the use. But proper maintenance is essential to extend its service life.
Detail
Second-hand high-frequency pipe welding machine, as an important equipment in industrial pipe production, can provide stable performance despite the use. But proper maintenance is essential to extend its service life.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn