MENU

/
/
Common faults of used welded pipe units

Common faults of used welded pipe units

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-12-25 11:30
  • Pvs:

【概要描述】There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.

Common faults of used welded pipe units

【概要描述】There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-12-25 11:30
  • Pvs:
Detail

There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.

 

Scratch

The scratches of the tube blank in the used welded pipe machines are mainly caused by two parts, ① scratches of the guide mechanism . ② the extrusion welding mechanism is scratched.

 

① Scratches of the guide mechanism

Scratches on the guide parts generally occur on both sides of the tube blank. If the guide structure with the guide sleeve is not properly adjusted, there will also be frictional scratches on the upper and lower surfaces of the tube blank. large and continuous. The main reason is that the height position of the guide sleeve is incorrect, or after the upper and lower guide roller bearings are damaged, the tube blank cannot be well controlled, so that it is formed after friction with the guide sleeve. In addition, when the guide roller deviates too much from the rolling center line, and the relative difference between the axes of the guide sleeve and the guide roller is too large, it will also cause scratches on both sides of the tube blank.

 

Used welded pipe machines

 

②The extrusion welding mechanism is scratched

The scratches caused by the extrusion roller mainly occur at the bottom of the tube blank, and the reasons are roughly as follows:

(1) The hole type does not match

Weld extrusion structures include two-roll, three-roll and four-roll. As long as the combined hole patterns do not match, it is easy to cause scratches on the surface of the tube blank, and the two-roll structure is particularly prominent. There are many factors that cause the hole pattern to not match. Take the two-roller structure as an example, such as bearing damage; axial movement of the roller; different hole size;

 

(2) Highly matched

The lower edge of the extrusion roll pass should be consistent with the height of the rolling line, while the height of the guide roll is determined by the wall thickness of the tube blank. If the height of the guide roller is reduced to a certain limit, the edge fillet of the squeeze roll pass will cause scratches to the bottom of the tube blank, especially after the R fillet of the squeeze roll pass is sharpened, the scratches will more likely to happen.

 

Used welded pipe machines

 

(3) Insufficient squeezing force on the squeezing roller

Especially for the two-roller structure of the extrusion roller device, when the upper extrusion force is insufficient, under the action of the tension of the tube blank, the roller shaft will have an upper elevation angle, so that the rounded corners of the edge R of the hole shape protrude, thereby causing the lower part of the tube blank. scratched. When the rounded corners of the squeeze roll hole type R are sharpened, the occurrence of scratching accidents will be aggravated.

 

The scratches of the tube blank in the used welding pipe machines are mainly caused by two parts, ① the guiding mechanism and ② the extrusion welding mechanism. As a result, the extrusion welding mechanism can be divided into (1) the hole type does not match (2) height matches (3) insufficient squeezing force on the squeezing roller.

关键词:

More News

Efficiency optimization of welding process of used high frequency welded pipe production line(2)
Efficiency optimization of welding process of used high frequency welded pipe production line(2)
The high-frequency welding process is the most widely used method for the production of welded pipes by used high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Detail
The high-frequency welding process is the most widely used method for the production of welded pipes by used high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Efficiency optimization of welding process of high frequency welded pipe production line(1)
Efficiency optimization of welding process of high frequency welded pipe production line(1)
The high-frequency welding process is the most widely used method for the production of welded pipes by high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Detail
The high-frequency welding process is the most widely used method for the production of welded pipes by high frequency welded pipe production line. It heats the metal by applying or inducing an electric current across the edge of the strip before the closing point of the open pipe, and presses the tube blank through squeeze rollers, The molten metal and inclusions are squeezed out of the weld pool to form a forged weld. But there is still a lot of room for improvement in this area. By designing and transforming the high-frequency welding process of the tube on the original basic configuration and operating it effectively, the welding process can be optimized, the welding efficiency can be improved, and the cost can be greatly reduced.
Defects caused by improper removal of internal burrs on used welded pipe machine
Defects caused by improper removal of internal burrs on used welded pipe machine
Whether the burr removal process of the used welded pipe machine is appropriate directly affects the quality of the welded pipe. Sometimes grooves are left due to the scraping of the scraper, which is rejected by the user as a welding defect, which brings serious economic losses to the steel pipe manufacturer.
Detail
Whether the burr removal process of the used welded pipe machine is appropriate directly affects the quality of the welded pipe. Sometimes grooves are left due to the scraping of the scraper, which is rejected by the user as a welding defect, which brings serious economic losses to the steel pipe manufacturer.
Analysis of the factors affecting the pipe making process of used high frequency welded pipe equipment (4)
Analysis of the factors affecting the pipe making process of used high frequency welded pipe equipment (4)
The main process parameters of high-frequency straight seam welded pipes manufactured by used high frequency welded pipe equipment include welding heat input, welding pressure, welding speed, size of opening angle, position and size of induction coil, position of impedance and other. These parameters have a great impact on improving the product quality, production efficiency and unit capacity of high-frequency welded pipes. Matching various parameters can make manufacturers obtain considerable economic benefits.
Detail
The main process parameters of high-frequency straight seam welded pipes manufactured by used high frequency welded pipe equipment include welding heat input, welding pressure, welding speed, size of opening angle, position and size of induction coil, position of impedance and other. These parameters have a great impact on improving the product quality, production efficiency and unit capacity of high-frequency welded pipes. Matching various parameters can make manufacturers obtain considerable economic benefits.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn