MENU

/
/
Common faults of used welded pipe mills production line forming machines (5)

Common faults of used welded pipe mills production line forming machines (5)

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-03-04 11:30
  • Pvs:

【概要描述】Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.

Common faults of used welded pipe mills production line forming machines (5)

【概要描述】Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-03-04 11:30
  • Pvs:
Detail

Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.

 

The phenomenon of "indenter" appears in the used welded pipe mills production line, which can be interpreted as "indenter" is actually a special manifestation of deviation, which generally occurs at the closed hole, and most of the tube blanks do not occur at the open hole. If it is overturned, one side edge of the tube blank is indented, and it mostly occurs when the tape is led. We call this phenomenon "indentation head" (Fig. 16).

 

Used welded pipe mills production line

 

There are two main reasons for "indenter":

① the shrinkage of the front vertical roller of the closed hole type is too large, or the center position of the vertical roller is not correct;

② the center of the closed pass and its front flat roll pass is not correct, or the pressure is insufficient, so that the tube blank floats back and forth during operation. Therefore, when leading the tape, pay attention to the specific performance of the head of the tube blank to find out the reason, and then deal with it in a timely manner. The edge indentation that occurs in the normal operation of the tube blank will be described in the welding seam accident.

 

The reason for the "indenter" phenomenon in the common failure of the forming machine of the used welded pipe mills production line is mainly because①The shrinkage of the front vertical roller of the closed hole type is too large, or the center position of the vertical roller is not correct. ②The center position of the closed pass and its front flat roll pass is not correct, or the pressure is insufficient, so that the tube blank swings back and forth during operation.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Detail
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Analyzing the roll life of a used ERW tube mill
Analyzing the roll life of a used ERW tube mill
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Detail
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn