MENU

/
/
China used pipe mills welded pipe production process specification—Water pressure testing process

China used pipe mills welded pipe production process specification—Water pressure testing process

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-18 11:30
  • Pvs:

【概要描述】In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

China used pipe mills welded pipe production process specification—Water pressure testing process

【概要描述】In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-18 11:30
  • Pvs:
Detail

In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

 

China used pipe mills

 

The sixth step we first understand the water pressure testing process of China used pipe mills

1. Before starting the machine, check whether each system of the hydraulic press is operating normally, and report any abnormality to the relevant leaders immediately.

2. Set the "manual, automatic" switch on the operation panel to the manual position, and the system enters the manual state. In manual operation, you must wait for the head to advance to the position before pressurizing the seal ring.

 

3. After the high-pressure water in the steel pipe is released, the sealing ring will be under pressure to prevent the sealing ring from being damaged.

4. When the equipment has an emergency failure, the equipment should be shut down immediately to eliminate the failure.

5. Set the "manual, automatic" switch on the panel to the automatic setting, and the system will enter the automatic working state.

 

China used pipe mills

 

6. During automatic operation, the flushing time, pressure holding time and required pressure value can be adjusted at any time according to the situation.

7. When an emergency fault occurs during automatic operation, the switch is turned to the stop position, and after the fault is removed, the operating state is returned to the initial position by manual operation.

 

After learning the water pressure testing process, we can carry out the actual operation principle of the steel pipe of China used pipe mills according to the water pressure testing process.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn