MENU

/
/
China used pipe mills welded pipe production process specification—slitting process

China used pipe mills welded pipe production process specification—slitting process

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-03 11:30
  • Pvs:

【概要描述】In the production of China used welded pipe mills , it is necessary to know the production process regulations of each equipment in order to operate the Chinese used welded pipe mills according to the production process regulations.

China used pipe mills welded pipe production process specification—slitting process

【概要描述】In the production of China used welded pipe mills , it is necessary to know the production process regulations of each equipment in order to operate the Chinese used welded pipe mills according to the production process regulations.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-03 11:30
  • Pvs:
Detail

In the production of China used welded pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the Chinese used welded pipe mills according to the production process regulations.

 

China used welded pipe mills

 

In the first step, we first understand the slitting process of Chinese used welded pipe mills

1. Check whether the external dimensions of the strip coils of the China used welded pipe mills are the strip steel required for production, and secondly, whether the strip steel is defective, and report any problems to the leader of the class in time.

2. After the feeder chooses the strip steel to check the safety of the spreader, he lifts the strip steel onto the loading trolley, leaving a certain size between the two cones for loading.

3. Drop the sling steel vertically so that its center and the center of the cone are approximately on the same horizontal line and between the two cones.

4. Open the shovel head of the straight-end machine while lowering the pressure roller, and then start the motor of the uncoiler to make the head turn on the plane of the shovel head.

 

5. Turn off the decoiler motor, turn on the straightening machine motor to drive the strip to move forward until the hydraulic shear.

6. Turn on the hydraulic shears, turn on the hydraulic shears to take the lead under the principle of no lack of ruler and no waste, to prevent the waste from splashing, and then lift the hydraulic shears.

7. Restart the leveler motor to feed the strip into the cutting blade.

8. Turn on the cutting blade motor to drive the strip into the slitting blade. After measuring the size, turn on the cutting blade motor to send the strip to the coiler section.

 

9. After the strip is cut, the blanker immediately attaches the newly cut waste wire head to the scrap edge coiler, and at the same time inspects whether the quality of the cut strip meets the requirements of the slitting process card;

10. When the cut strip reaches the reeling shaft, the blanker inserts the strip head into the coiling seam of the coiler;

11. Start the coiling motor until the whole strip is cut.

12. When the tail of each coil is on the reeling shaft, the blanking worker must tie it with the refined strip with iron wire or waste wire to prevent loose coils;

 

13. Open the hydraulic device to exit the steel coil and put it on the unloading trolley;

14. Put the cut steel coil neatly into the designated position.

After learning the slitting process, the actual operation principle of strip steel of Chinese used welded pipe mills can be carried out according to the slitting process.

 

Part of the content of this site comes from the Internet. This site only provides information storage. The copyright belongs to the original author. It does not bear the relevant legal responsibility and does not represent the views and positions of this site. Please contact and delete it if there is any infringement.

关键词:

More News

Welded pipe straightening method of used welded pipe machines
Welded pipe straightening method of used welded pipe machines
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Detail
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Common faults of used welded pipe units
Common faults of used welded pipe units
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Detail
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn