MENU

/
/
China used pipe mills welded pipe production process specification—pre-preparation and feeding process

China used pipe mills welded pipe production process specification—pre-preparation and feeding process

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-06 11:30
  • Pvs:

【概要描述】In the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the Chinese second-hand welded pipe equipment according to the production process regulations.

China used pipe mills welded pipe production process specification—pre-preparation and feeding process

【概要描述】In the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the Chinese second-hand welded pipe equipment according to the production process regulations.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-06 11:30
  • Pvs:
Detail

In the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the Chinese used welded pipe mills according to the production process regulations.

 

China used pipe mills

 

In the second step, we first understand the pre-loading process of China used pipe mills.

1. First check whether the appearance size of the strip coil meets the requirements of the production process card. If there is a problem, report to the leader of the class in time. When checking the quality of the strip coil, people should stand on the side of the strip coil to prevent the strip coil from falling down or unhooking. people.

 

2. After selecting the steel belt, instruct the crane operator to drop the hoisted steel belt vertically onto the loading trolley and adjust it. When hoisting the steel belt, use both gestures and spoken language. The hook must be hung firmly to prevent bumps and squeezing. Wait for the accident to happen.

3. After the strip coil is aligned, open the two cone heads evenly, leaving a certain size of steel coil between the two cone heads.

4. Start the loading trolley and move forward, and stop it when the center of the steel belt placed is in a straight line with the centers of the two cones.

 

5. Start the hydraulic lifting device so that the center of the steel coil and the center of the cone are approximately on the same horizontal line and on the midline of the rolling.

6. Evenly retract the two cone heads, so that the inner coil of the steel coil is close to the two cone head slopes.

7. After the cone head supports the steel coil, put down the hydraulic device, and at the same time exit the loading trolley, proceed to the lower coil and the material.

8. For the rolling mill without loading trolley, instruct the crane operator to safely put the strip steel into the tightening equipment of the decoiler.

 

After learning the pre-loading process, you can carry out the actual operation principle of strip steel of China used pipe mills according to the pre-loading process.

 

Part of the content of this site comes from the Internet. This site only provides information storage. The copyright belongs to the original author. It does not bear the relevant legal responsibility and does not represent the views and positions of this site. Please contact and delete it if there is any infringement.

关键词:

More News

Welded pipe straightening method of used welded pipe machines
Welded pipe straightening method of used welded pipe machines
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Detail
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Common faults of used welded pipe units
Common faults of used welded pipe units
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Detail
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn