MENU

/
/
China used pipe mills welded pipe production process specification—Water pressure testing process

China used pipe mills welded pipe production process specification—Water pressure testing process

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-18 11:30
  • Pvs:

【概要描述】In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

China used pipe mills welded pipe production process specification—Water pressure testing process

【概要描述】In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-18 11:30
  • Pvs:
Detail

In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

 

China used pipe mills

 

The sixth step we first understand the water pressure testing process of China used pipe mills

1. Before starting the machine, check whether each system of the hydraulic press is operating normally, and report any abnormality to the relevant leaders immediately.

2. Set the "manual, automatic" switch on the operation panel to the manual position, and the system enters the manual state. In manual operation, you must wait for the head to advance to the position before pressurizing the seal ring.

 

3. After the high-pressure water in the steel pipe is released, the sealing ring will be under pressure to prevent the sealing ring from being damaged.

4. When the equipment has an emergency failure, the equipment should be shut down immediately to eliminate the failure.

5. Set the "manual, automatic" switch on the panel to the automatic setting, and the system will enter the automatic working state.

 

China used pipe mills

 

6. During automatic operation, the flushing time, pressure holding time and required pressure value can be adjusted at any time according to the situation.

7. When an emergency fault occurs during automatic operation, the switch is turned to the stop position, and after the fault is removed, the operating state is returned to the initial position by manual operation.

 

After learning the water pressure testing process, we can carry out the actual operation principle of the steel pipe of China used pipe mills according to the water pressure testing process.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Detail
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Analyzing the roll life of a used ERW tube mill
Analyzing the roll life of a used ERW tube mill
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Detail
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn