MENU

/
/
China used pipe mills welded pipe production process specification—Flat head process

China used pipe mills welded pipe production process specification—Flat head process

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-15 11:30
  • Pvs:

【概要描述】In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

China used pipe mills welded pipe production process specification—Flat head process

【概要描述】In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2021-12-15 11:30
  • Pvs:
Detail

In the case of the production of China used pipe mills, it is necessary to know the production process regulations of each equipment in order to operate the China used pipe mills according to the production process regulations.

 

China used pipe mills

 

The fifth step we first understand the flat head process of China used pipe mills

①Before work, first adjust the specific position of the flat blade according to the specifications and models of the processed steel pipe, replace the corresponding block specifications, and adjust the elevation position of the tooth plate of the walking beam. When installing the tool, you should pay attention to the height of the two milling cutters of each power head to the tool ground as much as possible. When installing, put the tool into the bayonet of the cutter head and lock it with screws. The radial direction should be determined according to the pipe diameter. When the position of the blade needs to be chamfered, adjust the installation angle of the cutter head according to the angle of the chamfer. It should be noted that: the radial position of the chamfering knife should be as accurate as possible, and the roundness of the steel pipe should be higher than the national standard. If necessary, a tool setting model should be used.

 

②Turn on the power head motor, manually feed, step up, push, step, etc., adjust the position of the power head to return to the set zero position. The position of the zero position is determined by the position of the proximity switch. There are two proximity switches on both sides of the zero position, as the limit position of the power head movement, which plays a protective role. After all actions are confirmed to be correct, manually move the two steel pipes to the pushing position and push them all the way. Pull the switch to the automatic state, and the working process will be carried out automatically at this time. It should be noted that if the parameters have not been tested after setting, it is best to manually complete a few working cycles to verify the practicability of the parameters. When the parameters are approved, it is best to record them for future use. . When the stepping mechanism rotates to send a signal, the solenoid valve of the clamping cylinder is opened, the steel pipe is clamped, and a signal is sent, the power head feeds, and the roller table is opened while clamping, and the steel pipe is pushed and pressed. The program decelerates and stops; when the power head is finished and quickly returns, the solenoid valve of the clamping cylinder changes direction and the clamping is released. For the sake of safety, the change of the proximity switch signal is used to detect the clamp return, and check whether it is returned. If it does not return to the original position, the following actions will not be performed. After returning to the position, the stepping mechanism moves to move the flat-headed steel pipe to the next working position or out, and at the same time move the steel pipe to be processed to the working position, and then perform the flat-head cycle operation according to the above procedure.

 

After learning the flat head process, you can perform the actual operation principle of the steel pipe of China used pipe mills according to the flat head process.

关键词:

More News

Welded pipe straightening method of used welded pipe machines
Welded pipe straightening method of used welded pipe machines
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Detail
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Common faults of used welded pipe units
Common faults of used welded pipe units
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Detail
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn