MENU

/
/
Analysis of the factors affecting the pipe making process of high frequency welded pipe equipment(1)

Analysis of the factors affecting the pipe making process of high frequency welded pipe equipment(1)

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-04-12 11:30
  • Pvs:

【概要描述】The main process parameters of high-frequency straight seam welded pipes manufactured by high frequency welded pipe equipment include welding heat input, welding pressure, welding speed, size of opening angle, position and size of induction coil, position of impedance, etc. These parameters have a great impact on improving the product quality, production efficiency and unit capacity of high-frequency welded pipes. Matching various parameters can make manufacturers obtain considerable economic benefits.

Analysis of the factors affecting the pipe making process of high frequency welded pipe equipment(1)

【概要描述】The main process parameters of high-frequency straight seam welded pipes manufactured by high frequency welded pipe equipment include welding heat input, welding pressure, welding speed, size of opening angle, position and size of induction coil, position of impedance, etc. These parameters have a great impact on improving the product quality, production efficiency and unit capacity of high-frequency welded pipes. Matching various parameters can make manufacturers obtain considerable economic benefits.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-04-12 11:30
  • Pvs:
Detail

The main process parameters of high-frequency straight seam welded pipes manufactured by high frequency welded pipe equipment include welding heat input, welding pressure, welding speed, size of opening angle, position and size of induction coil, position of impedance, etc. These parameters have a great impact on improving the product quality, production efficiency and unit capacity of high-frequency welded pipes. Matching various parameters can make manufacturers obtain considerable economic benefits.

 

1.Welding heat input

When the high frequency welded pipe equipment runs high-frequency straight seam welded pipe welding, the welding power determines the amount of heat input to the welding. When the external conditions are certain and the input heat is insufficient, the edge of the heated strip cannot reach the welding temperature, and still maintains the welding temperature. A solid structure that forms a cold weld and cannot even fuse. The lack of fusion caused by too little welding heat input is shown in Figure 1.

 

High frequency welded pipe equipment

 

Figure 1 Unfused resulting from too small heat input

 

This lack of fusion during inspection usually manifests as unqualified flattening test, bursting of steel pipe during hydraulic test, or cracking of weld seam during straightening of steel pipe, which is a serious defect. In addition, the welding heat input is also affected by the quality of the edge of the strip. For example, when there is a burr on the edge of the strip, the burr will cause ignition before entering the welding point of the squeeze roller in the process of high frequency welded pipe equipment, resulting in welding power. The loss of heat reduces the heat input, resulting in an unfused or cold weld. When the input heat is too high, the edge of the heated strip exceeds the welding temperature, resulting in overheating or even overburning, and the weld will crack after being stressed. The blisters and holes formed by excessive heat input are shown in Figure 2.

 

High frequency welded pipe equipment

 

Fig. 2 Trachoma and holes caused by excessive heat input

 

These defects are mainly manifested in the failure of the 90° flattening test, the failure of the impact test, and the burst or leakage of the steel pipe during the hydraulic test.

 

Part of the content of this site comes from the Internet, this site only provides information storage, the copyright belongs to the original author, does not bear relevant legal responsibility, does not represent the views and positions of this site, if there is any infringement, please contact to delete.

关键词:

More News

Welded pipe straightening method of used welded pipe machines
Welded pipe straightening method of used welded pipe machines
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Detail
The problem of straightening the welded pipe often occurs when the used welded pipe machines is used to make pipes. For the straightening of welded pipes, we will explain to you how to make the pipes straightened by used welded pipe machines. Pay attention to the following requirements.
Common faults of used welded pipe units
Common faults of used welded pipe units
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Detail
There are relatively many failures of used welded pipe machines, and the causes of failures are also more complicated. Often, one result is caused by multiple reasons, or one cause can cause several results. Some failures are tricky to deal with. Let's start with a brief description of the scratch accident.
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines (5)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation ② scratches ③ "indenter" phenomenon ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ③ "indenter" phenomenon.
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines (4)
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Detail
Common faults of used welded pipe mills production line forming machines can be divided into ① deviation. ② scratches. ③ "indenter" phenomenon. ④ "drill belt" phenomenon. In order to let everyone understand the common faults of the molding machine in detail, we will introduce ② scratches.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn