MENU

/
/
Analysis of common faults of used welded pipe equipments sizing machine (2)

Analysis of common faults of used welded pipe equipments sizing machine (2)

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-12-21 11:30
  • Pvs:

【概要描述】In contrast, the failure rate of the sizing machine is the lowest, and it is easier to deal with. The common production accidents of the used welded pipe equipments sizing machine are as follows: ① Scratches. ②Drilling pipe. ③The tube is not round.

Analysis of common faults of used welded pipe equipments sizing machine (2)

【概要描述】In contrast, the failure rate of the sizing machine is the lowest, and it is easier to deal with. The common production accidents of the used welded pipe equipments sizing machine are as follows: ① Scratches. ②Drilling pipe. ③The tube is not round.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-12-21 11:30
  • Pvs:
Detail

In contrast, the failure rate of the sizing machine is the lowest, and it is easier to deal with. The common production accidents of the used welded pipe equipments sizing machine are as follows: ① Scratches. ②Drilling pipe. ③The tube is not round.

 

In order to let everyone understand the common faults of used welded pipe equipments sizing machines, we analyze the common faults of used welded pipe equipments sizing machines — drill pipes.

 

Used welded pipe equipment

 

Drill pipe

Drill pipe problems are rare, and generally occur more often when thin-walled pipes are produced. This is mainly because the rigidity of thin-walled pipes is poor, and the thin-walled pipes are easily bitten by the rollers. Therefore, the following problems in production will cause drill pipe accidents.

 

(1) Bearing damage. After the bearing of the lower flat roll is damaged, under the pressure of the upper flat roll, the rolling line height of the pipe will drop, and the pipe will easily drill into the lower roll edge of the vertical roll pass. If the vertical roller bearing is damaged, the gap between the upper and lower roller edges will increase, and the pipe will also drill into the gap at any time.

 

(2) The center of the hole pattern is not correct. Whether it is a flat roller or a vertical roller, when the center of the hole pattern is not correct, it will lead to the phenomenon of drilling pipe. When the vertical roller is out of alignment, under its misdirection, the pipe will be drilled into the gap of the roll edge of the flat roller. Improper timing of the flat roll will also cause the pipe to drill into the gap in the roll edge of the flat roll. This drilling phenomenon generally does not occur in the production of thick-walled pipes unless the center of the hole pattern is too far off. Drill pipe is more likely to occur only when producing thin-walled pipes with small diameters.

 

Used welded pipe equipments

 

If the used welded pipe equipments has common failures of the sizing machine, the drill pipe should pay attention to these two aspects (1) bearing damage. (2) The center of the hole pattern is not correct. Hope to be of some help to you. Our company has many brands and wide resources, there is always one suitable for you. You only need to inform us of your pipe manufacturing needs, and our company will provide you with used welded pipe equipments that really suits your needs. Welcome new and old customers to come to consult and order.

关键词:

More News

Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (2)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me first introduce the solution (2) of the fine forming hole pattern .
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
Solution for thick wall tube forming of used round pipe to square pipe machines(2)
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Detail
In the welded pipe industry, people generally regard welded pipes with a wall thickness to outside diameter (thickness-to-diameter ratio) of 12%≤t/D≤18% as thick-walled pipes. Difficulties in used round pipe to square pipe machines, clearly put forward the adjustment methods of thick-walled tube forming.
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to difficulties in thick-walled pipe forming of directly forming to square pipe mill (1)
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Detail
Solutions to solve the difficulties in forming thick-walled tubes of directly forming to square pipe mill include special forming unit solutions, rough forming pass solutions, fine forming pass solutions and comprehensive solutions. Let me introduce the solution to the difficult forming of thick-walled tube(1).
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn