MENU

/
/
Analysis of common faults of used welded pipe equipments sizing machine (1)

Analysis of common faults of used welded pipe equipments sizing machine (1)

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-03-03 11:30
  • Pvs:

【概要描述】In order to let everyone understand the common faults of used welded pipe equipments sizing machines, we analyze the common faults of used welded pipe equipments sizing machines — drill pipes.

Analysis of common faults of used welded pipe equipments sizing machine (1)

【概要描述】In order to let everyone understand the common faults of used welded pipe equipments sizing machines, we analyze the common faults of used welded pipe equipments sizing machines — drill pipes.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-03-03 11:30
  • Pvs:
Detail

In contrast, the failure rate of the sizing machine is the lowest, and it is easier to deal with. The common production accidents of the used welded pipe equipments sizing machine are as follows: ① Scratches. ②Drilling pipe. ③The tube is not round.

 

In order to let everyone understand the common faults of used welded pipe equipments sizing machines, we analyze the common faults of used welded pipe equipments sizing machines — drill pipes.

 

Used used welded pipe equipments

 

Drill pipe

Drill pipe problems are rare, and generally occur more often when thin-walled pipes are produced. This is mainly because the rigidity of thin-walled pipes is poor, and the thin-walled pipes are easily bitten by the rollers. Therefore, the following problems in production will cause drill pipe accidents.

 

(1) Bearing damage. After the bearing of the lower flat roll is damaged, under the pressure of the upper flat roll, the rolling line height of the pipe will drop, and the pipe will easily drill into the lower roll edge of the vertical roll pass. If the vertical roller bearing is damaged, the gap between the upper and lower roller edges will increase, and the pipe will also drill into the gap at any time.

 

Used used welded pipe equipments

 

(2) The center of the hole pattern is not correct. Whether it is a flat roller or a vertical roller, when the center of the hole pattern is not correct, it will lead to the phenomenon of drilling pipe. When the vertical roller is out of alignment, under its misdirection, the pipe will be drilled into the gap of the roll edge of the flat roller. Improper timing of the flat roll will also cause the pipe to drill into the gap in the roll edge of the flat roll. This drilling phenomenon generally does not occur in the production of thick-walled pipes unless the center of the hole pattern is too far off. Drill pipe is more likely to occur only when producing thin-walled pipes with small diameters.

 

If the used welded pipe equipments has common failures of the sizing machine, the drill pipe should pay attention to these two aspects (1) bearing damage. (2) The center of the hole pattern is not correct. Hope to be of some help to you. Our company has many brands and wide resources, there is always one suitable for you. You only need to inform us of your pipe manufacturing needs, and our company will provide you with used welded pipe equipments that really suits your needs. Welcome new and old customers to come to consult and order.

关键词:

More News

Analyzing the roll life of a used ERW tube mill
Analyzing the roll life of a used ERW tube mill
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
Detail
In the production of used ERW tube mills, the roll is the key and important special tool. Roll consumption is also a key tool for manipulating product costs. In addition, the normal operation of the roll will directly affect the output and quality of welded pipe manufacturing. Therefore, welded pipe manufacturers attach great importance to and strive to improve the service life of the roll.
How to extend the service life of high frequency welded pipe equipment
How to extend the service life of high frequency welded pipe equipment
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Detail
The service life of high frequency welded pipe equipment is of concern to everyone. The contribution made in the welding industry is immeasurable, and the care of it by customers should be paid more attention. So how can the service life of high frequency welded pipe equipment be extended in the actual production process?
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Adjusting the welding seam position of square and rectangular pipes made by directly forming to square pipe mill (2)
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Detail
Judging that the quality of the square tube produced by the directly forming to square pipe mill meets the standard is based on a large number of inspection data of the microhardness of the weld and the microhardness of the base material. The former is much higher than the latter. It is for this reason that the weld is usually not placed at a positive angle, but placed within t~(t+5mm) from the corner edge to reduce the risk of weld cracks. This requires effective control of the weld position. Control methods include forming roll method, guide roll method and sizing roll method.
Welding and rolling bottom line and sizing rolling bottom line in high frequency welded pipe machine
Welding and rolling bottom line and sizing rolling bottom line in high frequency welded pipe machine
The rolling line of high frequency welded pipe machine is all rolls on the welded pipe unit, including leveling rolls, forming flat rolls, guide rolls, squeeze rolls, deburring idlers, calendering rolls, sizing rolls, straightening rolls and other rolls. It is also the reference line for the installation and adjustment of related auxiliary equipment such as uncoilers, spiral loopers, flying saws, conveyor rollers, etc. It is the general term for the rolling bottom line and rolling center line, just like the human body. The spine plays a pivotal role in all process parameters of welded pipe production.
Detail
The rolling line of high frequency welded pipe machine is all rolls on the welded pipe unit, including leveling rolls, forming flat rolls, guide rolls, squeeze rolls, deburring idlers, calendering rolls, sizing rolls, straightening rolls and other rolls. It is also the reference line for the installation and adjustment of related auxiliary equipment such as uncoilers, spiral loopers, flying saws, conveyor rollers, etc. It is the general term for the rolling bottom line and rolling center line, just like the human body. The spine plays a pivotal role in all process parameters of welded pipe production.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn