MENU

/
/
Used ERW tube mills, how to adjust the squeeze roll "up one next two"

Used ERW tube mills, how to adjust the squeeze roll "up one next two"

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-01-28 11:30
  • Pvs:

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

Used ERW tube mills, how to adjust the squeeze roll "up one next two"

【概要描述】When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

  • Sort:Information
  • Auth:
  • Source:
  • Release time:2022-01-28 11:30
  • Pvs:
Detail

When the used ERW tube mills is used to make welded pipes, the judgement of the qualified quality of the welded pipe depends on the control of the squeeze roller, so the control of the squeeze roller is very important. There are many ways to control the squeeze roll, and "up and down two" is one of the squeeze roll methods.

 

Used ERW tube mills

 

Although the "up one down two" three-roller extrusion method has the characteristics of independent adjustment, three-roller unified adjustment, overall rotation and easy adjustment of the It covers 120 degrees, and the diameter and load capacity of each roller is effectively reduced, which avoids many of the disadvantages of the two-roller and the top three-roller. However, it is still impossible to avoid the existence of the independent top-roller three-roll squeeze mode. Shortcomings. Because of the small roll diameter of the used ERW tube mills, its bypass current is much smaller than that of the "two on one side" top roll extrusion device. However, equipment manufacturing also has the problems of relatively high technical requirements, processing accuracy requirements and relatively high cost, and relatively difficult adjustments. Only a few manufacturers currently use it.

 

The above is the method of adjusting the squeeze roll of the used ERW tube mills "up one down two", the next issue will introduce the method ④ "two top rolls and two side vertical rolls". If you need it, you can pay attention to the method in the next issue. At the same time, if you need used welded pipe equipments, please contact us. You only need to inform us of your pipe-making needs, and our company will provide you with used welded pipe equipments that really suits your needs.

关键词:

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products(1)
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Improving lubricating effect of flying saw on used welded pipe equipment
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Why does the used roll forming machine flying saw saw lack of lubrication?
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Weld quality failure caused by used welded pipe machines (9)
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province

Recommendation

Online Inquiry

留言应用名称:
底部留言
描述:

LINK

Contact Us

Tel (wechat): 13336487288
Wechat:+86 13336487288

WhatsApp:+86 13336487288
Email: zty@usedpipemill.com

Address: No. A99, Lecong Avenue East, Lecong Town, Foshan City, Guangdong Province

QRCODE

Copyright 0 2021 jinyujie. 粤ICP备13051810号 Powerby:  300.cn