Phone：+86-13336487288
whatsapp：+86-13336487288

/
/
Used square pipe machines to adjust the diagonal of square and rectangular tube

Used square pipe machines to adjust the diagonal of square and rectangular tube

• Sort：Information
• Auth:
• Source:
• Release time：2022-07-30 11:30
• Pvs：

【概要描述】The essence of adjusting the diagonals of the used square pipe machine is to adjust the square of the square tube. In theory, if the two diagonals of the square tube are equal, the square tube is square. But not necessarily for the rectangular tube in physical form.

Used square pipe machines to adjust the diagonal of square and rectangular tube

【概要描述】The essence of adjusting the diagonals of the used square pipe machine is to adjust the square of the square tube. In theory, if the two diagonals of the square tube are equal, the square tube is square. But not necessarily for the rectangular tube in physical form.

• Sort：Information
• Auth:
• Source:
• Release time：2022-07-30 11:30
• Pvs：
Detail

The essence of adjusting the diagonals of the used square pipe machine is to adjust the square of the square tube. In theory, if the two diagonals of the square tube are equal, the square tube is square. But not necessarily for the rectangular tube in physical form.

The premise of correct diagonal adjustment

The prerequisite for the correct diagonal adjustment of the used square pipe machine is that the theoretical diagonal length, the actual r-angle size and the measurement position determined by the hole type orientation are indispensable.

(1) Theoretical diagonal length. According to the geometric size of the square tube, the diagonal length C and C moment of the square moment management theory can be obtained as:

Before each adjustment, the theoretical diagonal length of the square rectangular tube of the corresponding specification must be calculated (or given by the process parameters), so that it can be used as a reference during adjustment.

(2) Confirm that the angle r is basically the same. Using the R gauge to measure the r-angle, according to the above formula, it can be known that only the diagonal measured when the four r-angles are basically equal in size can correctly reflect whether the rectangular tube is at right angles.

(3) The measurement position is accurate. The formula calculates the maximum value of the diagonal. If the measurement position is slightly off, then the measured size cannot truly reflect the length of the diagonal, and thus it is impossible to judge whether the tube is square.

For example: when 40mm*80mm rectangular tube r=5mm, the correct measurement angle is 23.199° instead of arctan(40/80)=26.565°.

The relationship between the diagonal measurement angle β of the rectangular tube and the tube angle r is shown in the following formula:

Therefore, the method of judging the square of the square tube by measuring the diagonal can only be used as a reference.

The upper and lower diagonals are larger than the left and right diagonals. The used square pipe machine can be adjusted in the following aspects:

(1) Properly loosen the final vertical roller (there is a flat roller afterwards). This adjustment action is suitable for fine-tuning in the production process.

(2) Properly press down the final flat roller. This adjustment measure firstly depends on whether the dimensions of the A and B sides of the rectangular tube are allowed, and it is suitable for use when the dimensions of the A and B sides are both on the wrong side.

From the above adjustment actions, we can see that special-shaped tube adjustments should pay special attention to the correlation and negative effects between the adjustment actions, as well as the positive effects.

For example, the adjustment action mode (2), if the size of A and B surface is too large, after the upper flat roller is pressed down, the purpose of reducing the diagonal line in the vertical direction can be achieved, and the size of A and B surface can be reduced by the way. Killing two birds with one stone, this is a positive effect, and can be used as the first adjustment action. On the contrary, it can only be used as a candidate adjustment measure.

More News

Factors and various influences to ensure the quality of used high frequency welded pipe machine welded pipe products（1）
Time of issue : 2023-10-31
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Detail
In the process of producing welded pipes with used high frequency welded pipe machine, how to ensure that the product quality meets the requirements of technical standards and the needs of customers, it is necessary to analyze the factors affecting product quality in the production process of steel pipes.
Improving lubricating effect of flying saw on used welded pipe equipment
Time of issue : 2023-10-28
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Detail
Through the technical improvement of the used welded pipe equipment, the lubrication of the gear and rack of the flying saw has been effectively improved, and the specific performance is as follows:
Why does the used roll forming machine flying saw saw lack of lubrication?
Time of issue : 2023-10-25
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Detail
When the used roll forming machine produces steel pipes, the pipe fittings move at a constant speed according to the set speed, and the saw car is stationary relative to the unit before the sawing process. When the steel pipe reaches the set length, the clamping device of the saw car clamps the steel pipe, and the drive mechanism drives the saw car to move with the steel pipe and perform the sawing process until the sawing operation is completed. When the sawing process of the flying saw is completed, the driving device drives the saw carriage to return to the initial position. The reciprocating motion of the saw car is realized by the relative movement of the rack at the bottom of the saw car and the gear fixedly installed on the machine bed system.
Weld quality failure caused by used welded pipe machines (9)
Time of issue : 2023-10-22
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Detail
When manufacturing welded pipes for used welded pipe machines, judging that the quality of the welded pipes meets the standard depends on the quality of the welds. Therefore, the quality of the weld is very important, so sometimes it is necessary to rule out the quality of the weld. We perform analyses to understand weld quality failures.
Contact information
Tel: +86-13392281699
Wechat: 13392281699
Email: zty@usedpipemill.com
Company address:No. A99, East Lecong Avenue, Lecong Town, Foshan City, Guangdong Province